Sharif Digital Repository

The role of initiators with different reactivities on the process cycle of nonisothermal resin transfer molding (RTM) was examined using the numerical simulation. A new process model was developed based on flow, heat and mass transfer equations combined with an appropriate mechanistic kinetics model which elucidates the functions of the initiators in the system. The process cycle of RTM with both single initiator and dual-initiator (combination of two initiators) was analyzed. The numerical simulations revealed that the single initiator with high reactivity reduces the cycle time, but there is a risk of incomplete mold filling and nonuniform temperature distribution. For dual-initiator... 

A comparative study on the uptake properties of alginate microcapsules containing Cyanex 302 extractant, Lewatite TP 214 chelating resin, and Amberlite 200CT strongly acidic ion exchanger has been conducted using Ag+ as the target ion. The study resulted in an analytical formula, as well as three phenomenological breakthrough formulas that are also applicable in other fixed-bed operations. It also demonstrated a close similarity of the uptake properties of alginate microcapsules (MCs) and the chelating resins. Advantages of MCs over chelating resins include ease of preparation, ability to immobilize different extractants, and, most remarkably, an enormous distribution factor (Kd ≈ 106... 

In the present investigation, mold filling process of resin injection/compression molding (RI/CM) is compared with resin transfer molding (RTM) for simple mold geometry. To do this, analytical solutions are obtained for RI/CM in unidirectional flow. Based on the analytical solutions, flow front progression and pressure distribution are compared with RTM at different fiber content. The results indicate that the RI/CM reduces the mold filling time significantly, particularly for composite parts with higher fiber content  

Very fine alumina nanoparticles were loaded in novolac type phenolic resin (PF) using solution mixing method. The concentration of nanoalumina in PF was varied between 2.5 to 20 wt%. All the compounds were compression molded and then subjected to scanning electron microscopy (SEM), tensile, flexural, and dynamic mechanical analysis (DMA) tests. SEM analysis showed that the nanoalumina were dispersed uniformly at low concentrations, however, at high concentrations, dispersion was suppressed leading to agglomerates in the composites. Mechanical testing revealed that the nanoalumina had a great influence on the strength and stiffness of PF resin particularly at concentrations below 5 wt%.... 

The effect of loading rate on toughening mechanisms of rubber-modified epoxy resin was investigated using amine-terminated butadiene acrylonitrile (ATBN) rubber. Rubber-modified samples were tested at various loading rates in the range of 1-1000 mm/min. At low loading rates, modified resin exhibited a high fracture toughness, which decreased by increasing the rate of loading. At higher loading rate a transition region was observed, where the fracture toughness did not change noticeably with increasing the loading rate. Beyond the transition region, the resin fracture toughness dropped dramatically to the level of unmodified epoxy. Fractography of the damage zone showed different toughening... 

In recent years, the behavior of crude oil interfacial tension (IFT) as a function of salt concentration have been investigated. The results found in literature are highly controversial, thus the current experimental study aimed to clarify the reasons behind this by developing a methodology based on extracting asphaltene and resin from three different crude oils and performing elemental analysis on them. In addition, the effect of salinity on the IFT of three studied crude oil was compared with the synthetic crude oil consisted of different weight percent (wt%) of asphaltene and resin in toluene. The obtained results revealed that the IFT of crude oil as a function of salinity depended not... 

The present work focused on the characterization of mechanical properties of novolac phenolic resin (PF) filled with two types of clays, including modified and unmodified ones, and multiwalled carbon nanotube (MWCNT). It was found that the solution mixing method is able to disperse the nanoparticles within the PF resin appropriately. It was also shown that the unmodified clay (Closite Na+) has the highest influence on the mechanical properties possibly due to the good level of dispersion as well as the good interfacial interaction. Theoretical analysis based on the rubber elasticity theory showed that the nanoparticles influence the evolution of crosslinking density and network structure  

Although the capability of using sulfate anion as a wettability modiffier is well established, no systematic investigation on the effect of sulfate ions and natural surfactants in the crude oil including asphaltene and resin on the interfacial tension (IFT) of acidic crude oil (ACO)/sulfate were performed. In this regards, the fluid/fluid interactions are tested through the IFT measurements for ACO, asphaltene and resin extracted from ACO in the presence of sulfate salts including Na2SO4, MgSO4 and CaSO4 while the concentration of each salt ranges between 0 and 45000 ppm. The obtained results demonstrate that the capability of asphaltene molecules is higher for IFT reduction compared with... 

In compression resin transfer moulding (CRTM), resin flows inside a mould filled with fibrous reinforcement as a result of resin injection and mould compression. This process facilitates the resin flow through the fibrous reinforcement particularly for high fiber content parts. This paper presents the numerical simulation of filling process of CRTM in full three-dimensional domain. A mathematical model of three-dimensional resin flow inside the CRTM mould is presented. An effective elastic modulus is introduced for multi-layer preforms connecting the mould closing speed to deformation rate of individual layers. Control volume/finite element method (CV/FEM) is used and the numerical algorithm... 

This work presents the catalytic graphitization process of phenolic resins (PR's) by addition of in situ nano-Fe particles as catalyst. Pyrolysis treatments of prepared compositions including various contents of nano-Fe particles were carried out at 600–1200 °C for 3 h under reducing atmosphere and graphitization process were evaluated by different techniques such as X-Ray diffraction (XRD), Field Emission Scanning Electron Microscopy (FESEM), High Resolution Transmission Electron Microscopy (HRTEM), Simultaneous Thermal Analysis (STA) and Raman spectroscopy that mainly performed to identify the phase and microstructural analysis, oxidation resistance and extend of graphitized carbon... 

An efficient dye decolorization platform was developed through one-step hydrothermally route based on magnetic polymeric resin and employed in aqueous crystal violet (CV) adsorption. The polymer nanohybrid composed of ZnFe2O4 and hydroxybenzoic acid–resorcinol resin as metal and organic fragment, respectively. Several techniques such as X-ray diffraction, N2 – adsorption desorption, vibration sample magnetometer, field emission scanning electron microscopy and Fourier transform infrared spectroscopy were employed for characterization of as-prepared nanohybrid. CV adsorption showed low equilibrium time within 10 min with the adsorption capacity of 83.3 mg g–1. Regeneration of the sorbent... 

Toughness improvement of an epoxy resin and respective hoop wound composite were investigated systematically using amine-terminated butadiene acrylonitrile (ATBN) liquid rubber. Rubber modification improves fracture toughness of epoxy resin with slight reduction in the glass transition temperature (Tg), flexural and compressive properties of resin. Impact resistance of composite is improved by rubber modification similar to modified resin. Interlaminar shear strength (ILSS), compressive modulus and strength, and flexural strength of composite decreased slightly with rubber modification. To interpret the data, the void content of composite samples was determined and the damaged surfaces of... 

Impure rhenium and molybdenum bearing solution was passed through a column of Varian strong base anionic resin for selective adsorption of rhenium and molybdenum ions from the solution. Elution of molybdenum and rhenium was carried out using 2 N NaOH and 0.2 N NH4SCN, respectively. The effect of resin bed height on breakthrough time was investigated. Experimental and theoretical curves were compared with good agreement. The results showed that the behavior pattern of these curves was repeatable and almost constant. © 2006 Elsevier B.V. All rights reserved  

Unidirectional experiments were carried out for the evaluation of the unsaturated permeability of the reinforcement during the injection and the saturated permeability. Saturated permeability was found to govern the permanent flow established after filling of the cavity. The unsaturated permeability was evaluated by a linear regression in function of the position of the resin front during transient flow experiments performed at constant injection pressure. The difference between these two permeability values is also related to the pore structure of the fiber bed  

Numerical simulation of resin transfer molding (RTM) is known as a useful method to analyze the process before the mold is actually built. In thick parts, the resin flow is no longer two-dimensional and must be simulated in a fully three-dimensional space. This article presents numerical simulations of three-dimensional non-isothermal mold filling of the RTM process. The control volume/finite element method (CV/FEM) is used in this study. Numerical formulation for resin flow is based on the concept of nodal partial saturation at the flow front. This approach permits to include a transient term in the working equation, removing the need for calculation of time step to track the flow front in... 

This article examines the physical and mechanical characteristics of mixtures of two different synthetic rubbers, namely styrene-butadiene rubber (SBR) and nitril-butadiene rubber (NBR), with novolac type phenolicresin (PH). According to Taguchi experimental design method, it is shown that the addition of PH increases the crosslinking density of rubber phase probably due to its curative effects. Thermal analysis of the blends indicates that, contrary to NBR/PH blend, thermal stability of SBR/PH blend is dependent on sulfur content due to predominant polysulfidic crosslinks formed in SBR. Slight shift in glass-transition temperature (Tg) of pure SBR and NBR vulcanizates by the addition of PH...