Sharif Digital Repository

We study Hydrogen sulfide gas detection properties of pure and 1% copper oxide added WO3 thin films. The spin coated deposits on alumina substrates were annealed at 500 C for 1 hour in order to improve the crystallinity of the films. The sensitivity of pure tungsten oxide is poor even at temperatures of about 100 C but the doped samples exhibit good response to H2S gas. Our data show sensitivity of about 1500 in 10 ppm diluted gas in air at 100 C. The films are sensitive to the gas even at 250 ppb (sensitivity about 2) H2S concentration at 100 C but with rather long recovery time. Crystal structure, morphology and chemical composition of samples were studied by X-Ray diffraction (XRD),... 

By fabrication of several bolometric detectors on the YBCO film made of Metal-Organic Deposition (MOD) and the effect of pattering and film parameters on the optical responsivity of transition edge sensors is investigated. The low cost nonfluorine (MOD) method has been applied to fabricate YBCO thin films with different patterning parameters. The measurement results of the optical responsivity versus modulation frequency up to 100 KHz for these devices are reported  

Epitaxial cerium oxide (CeO2) buffer layer has been grown on lanthanum aluminate (LAO) single crystal substrates for fabrication of c-axis oriented YBa2Cu3O7-x (YBCO). Precursor solution of cerium acetylacetonates with viscosity of 0.6 centipoises was spin coated on the 1×1 cm area LAO substrates. The calcination was carried out by very slow ramp (1°C per minute) until the final temperature of 500°C in oxygen flow to remove most of the organic compounds. The final heat treatment has been done at 780°C by a ramp of 20° per minute in gas flow of mixed argon-oxygen with 5 Pa partial pressure of oxygen. The thickness of the deposited CeO2 buffer layer was 20 nm. Then, 100 nm thick YBCO film was... 

We theoretically demonstrate the tunabiltiy of terahertz random lasers composed of high temperature superconductor YBCO and ruby layers as active medium. The considered system is a one-dimensional disordered medium made of ruby grain and YBCO. Finite-difference time domain method is used to calculate the emission spectrum and spatial distribution of electric field at different temperatures. Our numerical results reveal that the superconductor based random lasers exhibit large temperature tunability in the terahertz domain. The emission spectrum is significantly temperature dependent, the number of lasing modes and their intensities increase with decreasing temperature. Also, we make some... 

Detectivity optimization of large-area freestanding-type YBCO superconducting bolometric detectors is theoretically and experimentally investigated. The effect of the device thermal parameters on the theoretical total noise-equivalent power based on background radiation, thermal fluctuation, and Johnson noise is considered. By analytical optimization of the total noise-equivalent power (NEP) of the device with respect to the thermal parameters and radiation modulation frequency, the maximum sensitivity and optimal thermal parameters of the bolometric detector are obtained. Relating device thermal parameters to the special case of the large substrate dimensions, the optimum device geometry is... 

The application of flat superconductor rings has been investigated in the structure of inductive shield-type high temperature superconducting fault current limiters, HT c-SFCL. A laboratory scale inductive shield-type HT c-SFCL has been designed and fabricated using flat superconductor rings. The fabrication process has been fully presented. YBCO powder has been used for the fabrication of superconductor rings. This fabrication process, being quite innovative, is introduced completely. The method of the trapped field measurement has been used for the critical current density measurement of the fabricated superconductor rings. The device with nominal current of 2 A was tested in a 30 V... 

We present the results of a bolometric transition-edge sensor made of a high-Tc superconductor YBCO thin film prepared by fluorine-free metal-organic deposition. The structure of the films was characterized by X-ray diffraction and scanning electron microscopy, and the superconducting properties were determined by R-T measurements. The applicability of the resulting film as an infrared sensor is reported here. The optical response in the range of near infrared and the noise characteristics of the patterned bolometer are measured and analyzed. The dependence of device sensitivity on the bias current and modulation frequency is also investigated. As it is presented in this paper, the results... 

Carbon nanotubes (CNTs) decorated with Cu2O particles were grown on a Ni catalyst layer deposited on a Cu substrate by thermal chemical vapor deposition from liquid petroleum gas. Ni catalyst nanoparticles with different sizes were produced in an electroplating system at 45 °C using the corrosive effect of H2SO4 which was added to solution. These nanoparticles provide the nucleation sites for CNT growth avoiding the need for a buffer layer. The surface morphology of the Ni catalyst films and CNT growth over this catalyst was studied by scanning electron microscopy (SEM). High temperature surface segregation of the Cu substrate into the Ni catalyst layer and its exposition to O2 at... 

A simple and efficient method was developed for fabricating spherical granules of CuO catalyst via a three-step procedure. In the first step, copper oxide nanoparticles were synthesized by hydrothermal decomposition of copper nitrate solution under supercritical condition. Then, they were immobilized in the polymeric matrix of calcium alginate, and followed by high-temperature calcination in an air stream as the third step, in which carbonaceous materials were oxidized, to result in a pebble-type catalyst of high porosity. The produced CuO nanoparticles were characterized by transmission electron microscopy (TEM) that revealed an average size of 5 nm, X-ray diffractometry (XRD), and thermo... 

Nanofluid is the term applied to a suspension of solid, nanometer-sized particles in conventional fluids; the most prominent features of such fluids include enhanced heat characteristics, such as convective heat transfer coefficient, in comparison to the base fluid without considerable alterations in physical and chemical properties. In this study, nanofluids of aluminum oxide and copper oxide were prepared in ethylene glycol separately. The effect of forced convective heat transfer coefficient in turbulent flow was calculated using a double pipe and plate heat exchangers. Furthermore, we calculated the forced convective heat transfer coefficient of the nanofluids using theoretical... 

A simple, efficient, and practical procedure for the synthesis of imidazo[1,2-a]quinoline and quinolino[1,2-a]quinazoline derivatives using CuO nanoparticles as a novel catalyst in excellent yields is described. The catalyst can be recovered conveniently and reused at least four times without any loss of activity  

An easy method for preparing CuO nanoparticles incorporated in a mesoporous structure was presented based on the thermal decomposition of a copper complex. The novel copper coordination compound of [Cu(anic)2]·0.75H2O (anic= 2-aminonicotinate) with the microflake morphology was synthesized through the reaction of 2-aminonicotinic acid (Hanic) and copper(II) nitrate. Using elemental analysis and Fourier transform infrared (FTIR) spectroscopy, the chemical composition of CuC12H11.5N4O4.75 was proposed. Calcination process at 550 °C for 4 h transformed the microflakes into CuO nanoparticles incorporated in a mesoporous structure. The FTIR peaks assigned to 2-aminonicotinate were completely... 

Copper and cobalt oxides supported on almond shell derived activated carbon (AC) with different loadings were synthesized by sequential and co-deposition-precipitation methods leading to Cu(shell)/Co(core)/AC, Co(shell)/Cu(core)/AC and Cu-Co(mixed)/AC catalysts that were subsequently used for catalytic oxidation of gaseous mixtures of toluene and cyclohexane in air in a tubular flow reactor. The catalysts and the support were characterized by Boehm test, Brunauer-Emmett-Teller (BET) surface area, X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy... 

This work describes the development of a novel electrochemical sensor based on electrodeposition of copper oxide nanoparticles onto carbon nanoparticle (CNP) film modified electrode for the analysis of the anti-HIV drug, nevirapine (NEV). The electrochemical experiments were performed using linear sweep and cyclic voltammetry. Atomic force microscopy was applied for surface characterization of the deposited modifier film (CuO-CNP) on glassy carbon electrode (GCE). No oxidation peak was observed for NEV on the bare GCE, but both CNP-GCE and CuO-CNP-GCE showed a distinctive anodic response towards NEV with considerable enhancement (276-fold and 350-fold, respectively) compared to CuO-GCE. The... 

Ultra fine CuO nanoparticles In the range of 2 ± 0.2 nm were synthesized by the supercritical hiydrotliermal method in a batch reactor. Itwas demonstrated that elevating the pH of the Cu2+ precursor solution to around 6 (neutral condition) not only does not lead to excessive agglomeration of the particles, but also reduces particle size and in general promotes their nanoscale characteristics. Prepared nanoparticles were immobilized in the biopolymcric matrix of barium alginate and calcined at different temperatures resulting in micro spherical granules of high porosity and elevated mechanical strength. The fabricated samples were characterized using x-ray diffractometry (XRD), transmission... 

CuO nanoparticles with average diameter of about 20. nm were accumulated on surface of sol-gel silica thin films heat treated at 300 °C in air. Heat treatment of the CuO nanoparticles at 600 °C in a reducing environment resulted in effective reduction of the nanoparticles and penetration of them into the film. While the thin films heat treated at 300 °C exhibited a strong antibacterial activity against Escherichia coli bacteria, the reducing process decreased their antibacterial activity. However, by definition of normalized antibacterial activity (antibacterial activity/surface concentration of coppers) it was found that Cu nanoparticles were more toxic to the bacteria than the CuO...