Sharif Digital Repository

Herein, a series of superhydrophobic thin polyacrylic resin-coated carbon black (CB)/hexagonal boron nitride (h-BN)@Fe3O4/cellulose composite papers with good flexibility, low density (~0.67 g/cm3), high electrical conductivity (~0.065 S/cm), good thermal conductivity (0.462 W.m−1. K−1), and with water contact angle (WCA) of 153° were successfully fabricated by a facile dip-coating/spraying method. The CB-BN@Fe3O4 distribution in cellulose matrix provided high electrical conductivity in the in-plane and thickness directions. The electrical conductivity in both in-plane and thickness directions increased by increasing the number of vacuum-assisted dip-coating cycles. Moreover, these... 

In this work, flexible thermoelectric fabrics, polyester/yarn fabrics coated with polyaniline/carbon nanotube (PANI/CNT) nanocomposite, were fabricated by sequential processing: (I) polyaniline/carbon nanotube nanocomposites preparation by a one-step in-situ polymerization and (II) dip coating of a mixture solution of CNT-doped PANI on a polyester/yarn fabric. Nanocomposites were synthesized with various CNT content (0.5, 2.5, 5, and 10 wt%) and characterized using different methods. The Seebeck coefficient and electrical conductivity measurements were used to determine their thermoelectric properties. The results revealed significant improvement in both electrical conductivity and the... 

The biodegradation behavior of Mg, coated by polymethyl methacrylate as well as polymethyl methacrylate (PMMA)−bioactive glass (BG) composite was investigated. Electrophoretic deposition and dip coating techniques were adopted to prepare composite coating using a suspension of different percentages of the above two chemical materials. The deposited coatings were characterized using SEM, EDS, FTIR, and water contact angle measurements. Biodegradation behavior study of the coated Mg was performed using linear polarization, impedance spectroscopy, and immersion tests in simulated body fluid. The compact and homogeneous composite coating was developed as evidenced by electron microscopy results.... 

In terms of manufacturability, there is a high tendency to deposit light-absorbing CuInS2 films by solution processing methods like ink-based depositions. In particular, for nanoparticle inks, the synthesis of highly dispersed and stable inks, with uniformity in the deposition process, is a serious challenge. Here, we demonstrate a novel two-step low-temperature CuInS2 film deposition method in which the In2S3 is deposited first. It then partially is converted into CuInS2 through the infiltration of Cu+ ions in the In2S3 layer in a dip-coating process. The resulting films are highly uniform, with diffraction peaks indicating the formation of pure CuInS2 phase. The proper stoichiometry of... 

In this work, flexible thermoelectric fabrics, polyester/yarn fabrics coated with polyaniline/carbon nanotube (PANI/CNT) nanocomposite, were fabricated by sequential processing: (I) polyaniline/carbon nanotube nanocomposites preparation by a one-step in-situ polymerization and (II) dip coating of a mixture solution of CNT-doped PANI on a polyester/yarn fabric. Nanocomposites were synthesized with various CNT content (0.5, 2.5, 5, and 10 wt%) and characterized using different methods. The Seebeck coefficient and electrical conductivity measurements were used to determine their thermoelectric properties. The results revealed significant improvement in both electrical conductivity and the... 

Interactions between the metal interconnect and glass sealant in the solid oxide cells stack are critical to retaining the system integrity. To address this issue, in the current study, 8YSZ coating is applied on the Crofer22 APU steel via sol-gel and dip-coating method. Dense and continuous 8YSZ coatings are obtained on Crofer22 APU substrates. X-ray diffraction and Raman spectroscopy results show that both cubic and tetragonal structures of 8YSZ are formed. A glass-based sealing paste is applied on bare and 8YSZ coated Crofer22 APU steel. The interfacial compatibility and chemical stability of steel/glass and steel/8YSZ/glass joint couples are investigated using SEM and EDS line scan... 

In this study, zirconia antistatic coatings were synthesized by a simple dip coating sol-gel route on glass substrates, then applied to polymer-based composites to potentially improve their dust or water repellent capabilities. The coating solution contained a precursor (ZrCl4), solvent (isopropanol) and coupling agent. FTIR spectra confirmed ZrO2 and ZrO compounds in both solution and antistatic coating. FE-SEM images indicated ZrO2 fibers’ thickness was controlled by changing ZrCl4 concentration (150 g–15 g ZrCl4/l) or relative humidity (20%–60%) during coating drying. Fibers grew thicker when decreasing the former or increasing the latter. The surface electrical resistivity for all... 

Application of corrosion resistant coatings is one of the most widely used means of protecting steel. Zinc coated (galvanize) steel, is well known for galvanic protection of steel substrates and nowadays, particular attention has been paid to the coupling of graphene oxide (GO) with metallic materials, in order to lessen corrosion rate. In this research, an isopropanol supercritical reducing environment prepared to make zinc ions bond directly with graphene oxides, to form a button shape hybrids of ZnO-Graphene (ZnOG). The hybridized bonding between zinc and graphene oxide is confirmed by Fourier Transform Infra-Red analysis. And the morphology revealed, using a Field Emission Scanning... 

Wettability is one of the most important factors which significantly influences solar still efficiency. Moreover, it determines the condensation mode, i.e., filmwise or dropwise condensation. In the present study, materials with different wettability were applied as the condensing surface to evaluate the effect of wettability on the distillate production of a single slope solar still. To compare the effects of dropwise and filmwise condensation on the condensate yield, the wettability of the condensing surface was changed by applying a nano-silicon solution according to a dip coating technique. All the experiments were conducted at three surface inclination angles. The results revealed that... 

Titanium dioxide is prepared by sol gel method from titanium tetraisopropoxide (TTIP) as precursor and likewise zinc oxide is prepared by sol gel method from zinc acetate dehydrate (ZAD) as precursor. The composite sols are prepared in three different molar ratios 90TiO2:10ZnO, 70TiO2:30ZnO and 50TiO2:50ZnO. Thin film deposition is carried out by dip coating technique. Crystal structure, surface morphology and photocatalytic activity of the prepared nanocomposite thin films are investigated. The antibacterial activity of the prepared nanocomposite thin film against E-coli ATCC 25922 bacteria is examined by placing the thin film in standard aqueous E-coli medium under UV light for 1, 2, 3 and... 

Abstract: This study aimed to understand the microstructural, optical, and electrical properties of tin-doped indium oxide (ITO) prepared with tetravalent and divalent tin salts. The influence of tin valence on the electrical, optical, structural, and morphological properties of the films were characterized by the mean of four-point probe, thermogravimetric analysis, differential thermal analysis (DTA), UV–Vis spectroscopy, X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and X-ray photoelectron spectroscope. XRD results revealed formation of cubic bixbyite structure of In2O3 with a small shift in major peak position toward lower angles with... 

In an attempt to reduce the oxidation and Cr evaporation rates, various protective coating layers with a nominal composition of NiCo 2-xFexO4 (x = 0, 0.5, 1) were deposited on the SUS 430 ferritic stainless steel substrate, as interconnect for solid oxide fuel cell application, by sol-gel dip coating method. Then, the coated samples were soaked at 750 C for 2.5 h in N2 and subsequently for 2.5 h in air. Phase composition and microstructure of the coatings were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Moreover, long-term isothermal oxidation experiment and area specific resistance (ASR) measurement were also carried out on the coated samples. Results... 

Lanthanum chromite coating occupies a noticeable position as a ceramic coating on metallic interconnects in solid oxide fuel cells because of its excellent electrical conductivity, high oxidation resistance and desirable chemical stability in both oxidizing and reducing atmospheres. In the present work, a sol-gel process based on the dip-coating technique was used to prepare dense and uniform coatings on metallic alloy for interconnect application (AISI 430 type). The effect of strontium and calcium doping into lanthanum chromite structure on electrical conductivity and oxidation behavior of the coated sample has been investigated. The oxidation behavior was evaluated by cyclic oxidation... 

In the present research, the introduction of multi-walled carbon nanotubes (MWCNTs) into the hydroxyapatite (HA) matrix and dip coating of nanocomposite on titanium alloy (Ti-6Al-4V) plate was conducted in order to improve the performance of the HA-coated implant via the sol-gel method. The structural characterization and electron microscopy results confirmed well crystallized HA-MWCNT coating and homogenous dispersion of carbon nanotubes in the ceramic matrix at temperatures as low as 500 C. The evaluation of the mechanical properties of HA and HA/MWCNT composite coatings with different weight percentages of MWCNTs showed that the addition of low concentrations of MWCNTs (0.5 and 1 wt.%)... 

A novel simple synthetic procedure for fabrication of high surface area nanostructured TiO2 electrode with uniform particles for photovoltaic application is reported. Modifying the TiO2 particulate sol by pH adjustment together with employment of a polymeric agent, so-called polymeric gel process, was developed. The polymeric gel process was used to deposit nanostructured thick electrode by dip coating incorporated in dye-sensitized solar cells (DSSCs). X-ray diffraction (XRD) analysis revealed that deposited film was composed of primary nanoparticles with average crystallite size in the range 21-39 nm. Field emission scanning electron microscope (FE-SEM) images showed that deposited film... 

Uniform nanostructure anatase films were coated on 316L stainless steel by the sol-gel dip coating method. Sols with different values of pH were applied. The corrosion protective behavior of coated samples was investigated by electrochemical measurements in 0.5 molar NaCl solutions on samples placed under UV illumination and dark condition using Tafel curves. It was found that in addition to acting as a physical barrier, anatase thin films are more protective under UV illumination due to photocathodic protection. Neutral sols give better protection due to formation of more uniform and less defective coatings  

In this study hydroxyapatite (HA)/zirconia/alumina composite coatings on titanium metal was carried out using Sol-Gel dip coating and calcination process. Hydroxyapatite-Alumina-Zirconia sol, coated samples in three processes by changing final sol stirring time, aging time, calcination temperature of synthesized powder and prepared coating and rate of coating. Some parts of prepared sol were also synthesized and became powder in all three processes. Scanning electron microscopy was used to estimate the particle size of the surface and for morphological analysis. The functional group and crystallization characteristics of the powders were analyzed using (FTIR) and X-Ray diffraction (XRD).... 

A hydrogen-selective nano-composite ceramic membrane was prepared by depositing a dense layer composed of SiO2 and Al2O 3 on top of a graded multilayer substrate using co-current chemical vapor deposition (CVD) method. The multilayer substrate was made by dip-coating a macroporous α-alumina tubular support by a series of boehmite solutions to get a graded structure. Using DLS analysis, it was concluded that decreasing hydrolysis time and increasing acid concentration lead to smaller particle size of boehmite sols. XRD analysis was carried out to investigate the structure of intermediate layer and an optimized calcination temperature of 973 K was obtained. SEM images indicated the formation... 

The low erosion resistance of titanium and its alloys has prevented their widespread application as joint implants. In addition, one essential requirement for the implants to bond with the living bone is the formation of a bone-like apatite on their surfaces in the host body. To enhance the erosion resistance of the surface, a diffused layer of TiB2 was formed at 1000uC on the commercial pure titanium. Hydroxyapatite was then coated on the boronised titanium by means of dip coating in a sol-gel solution. In order to confirm the biocompatibility of the specimens, they were soaked in a simulated body fluid for several days. The surface morphology of the specimens after exposure was studied by... 

Research and development efforts continue to improve oxidation resistance and electrical conductivity of solid oxide fuel cell (SOFC) interconnects. This research evaluates the performance of a ferritic stainless steel (AISI 430 - a candidate SOFC interconnect material) with and without a Co coating (via sol-gel dip coating technique) with various pre-treatments, during cyclic oxidation exposures up to 750°C in laboratory air. A pre-treatment exposure of Co coated samples to a 750°C reducing atmosphere (prior to oxidation exposures) led to the formation of an effective Co-based spinel oxide coating that lowers oxidation rates by more than 40 times, and substantially lowers area specific...