Sharif Digital Repository

Selection of appropriate coating system is the most important subject in corrosion control of buried pipelines. Corrosion control of buried pipelines is achieved by using a combination of barrier coatings and cathodic protection (CP). Applying barrier coating can decrease the protection current of CP. However, at the coating holidays the pipeline act as cathode generating hydroxyl ion and hydrogen electrochemically. Therefore the selected coating should be compatible with the alkaline condition.This research focuses on evaluating of an epoxy-tar and a urethane-tar based coating. Coatings performance has been tested by accelerated corrosion test methods (i.e. Salt spray according to ASTM... 

Syntheses of coats including nickel nano-particles by electrodeposition have been
investigated for over 10 years. A method of testing according to surface reply was chosen
to reveal the effect of each pulse parameters (including duty cycle, frequency, average
current density, off time (toff) and on time (ton)) and the effect of saccharin concentration
on electroplating cathode efficiency, nanostructure. Pulse electroplating test of nickel was
composed by 30 tests. Pulse electroplating with relatively high peak current density was
employed and saccharine was added to increase deposition and rate of nickel nucleation on
surface. According to the results of cathode... 

An optimization condition for obtaining Ni-Zn-P electroless alloy coating has been developed. The sulphate bath with sodium hypophosphate as a reducer and sodium citrate and ammonium chloride as complexing agents were used. The effect of variation in the pH level , temperature , time of deposition and reactants concentration on stability of bath, coating composition, microstructure, microhardness and corrosion resistance of coatings was investigated. The composition of coatings was obtained by using the EDAX analysis. To investigate coating morphology, SEM images were taken and to study the corrosion behavior of coatings potentidynamic polarization, Electrochemical Impedance Spectroscopy... 

Silver nanoparticles are widely used in different industries because of their antibacterial effects. Many synthesis methods were used to obtain silver nanoparticles. In this study the microwave method is used to synthesize nanosilver. This method is easier and faster in comparison to other methods. The effect of precursors’ concentrations, using different solvents, different remaining time in microwave and microwave power were studied. By increasing the reaction time, microwave power and using different solvents, nanosilver particle size varies from 2 nm up to 300nm. The TEM images, size distribution, XRD patterns and UV-visible spectrum are shown. The obtained nanosilver was used to observe... 

Reinforced concrete is one of the most important structural materials used in the construction industry worldwide. Nevertheless, certain physical and chemical factors in the service environment can contribute to its deterioration and failure. One of the most significant factors is the reinforcing steel bar (rebar) corrosion. In order to minimize the rebars corrosion, different kinds of coatings were investigated and evaluated by scientists. In this investigation comparative studies were performed on two different kinds of coated rebars (zinc-rich epoxy and polyamide epoxy coated rebars) and uncoated rebar. In order to evaluate these reinforced concretes, the adhesion, durability, thickness... 

Ni-P alloy coatings were electrodeposited using pulse current in a watt type bath in various conditions. The influences of different parameters were investigated and optimized for the highest amount of coating hardness using the Design Of Experiment (DOE) method. The optimized deposition parameters were current density 23.7 A/dm2, duty cycle 75%, frequency equal to 188 Hz, temperature equal to 70ºC and 17.5 gr/l of H3PO3. The DOE prediction of hardness for the optimized coatings was between 700 and 750 the achieved micro-hardness was about 725.8 HV. It was obtained that an increase of the current density will improve micro-hardness, decreases P content and increase deposition rate. Also, the... 

In this thesis, the hardness of Ni-Cr alloys is optimized by design of experiment (DOE) method (Central Composite Design) in pulse electrodeposition performed in chloride solution. Various parameters were evaluated for finding significant factors in pulse electrodeposition of Ni-Cr alloy. Frequency, duty cycle, current density and temperature were selected as effective factors. 30 experiments were designed by the central composite design method. Analyses of Variance (ANOVA) were performed on the results of these 30 experiments. The best models which can predict the hardness, Cr content, deposition rate, thickness and cathode efficiency of Ni-Cr alloy electrodeposits were found and... 

This research focuses on finding an appropriate method for increasing wear and corrosion resistance of hard coating TiN PVD and chromium. The substrate was made up of 42CrMo4 (DIN) steel (used for marine industries) and coated by TiN Arc PVD process and hard chromium electro-deposition. The results of these two coatings are compared and the better coating which is TiN Arc PVD is suggested. To find the best method for coating, several test studies are organized such as: the mechanical and tribological properties of TiN PVD and hard chromium coatings for wear and corrosion resistance applications are organized. The potentiodynamic polarization technique was used to measure the corrosion rate... 

The cathodic protection system was employed for protection of the reinforced concrete of the foundations using the mixed metal oxide anodes embedded in concrete for current distribution. . In this system, after required measurements for zone design calculation of the surfaces current density, IR drop and the circuit’s resistance has been measured. After specifying the appropriate locations for the reference Electrodes (Ag/AgCl) in order for cathodic protection monitoring these three electrodes are installed in three protection zones. After design and supply of all the materials, the installation was started. The protection criterion of steel in concrete was studied and all the measured... 

Many of the major structure over coastal waters in the Kish Island due to the aggressive condition are showing signs of reinforcement corrosion. Recent advances in the development of anodes make it practical to use zinc galvanic cathodic protection to protect this structure in this area. Five anode systems were tested on several samples as, (1) zinc metal spray applied by arc-spraying on the concrete, (2) a zinc foil with conductive adhesive backing, (3) a system of zinc mesh and grout jacket, (4) a system of zinc mesh and compression panels, and (5) a bulk zinc. These anodes are set up to comparison the effects of potential and current over the zinc galvanic cathodic protection during 4... 

Corrosion is a main problem for oil and gas industries at refineries and petrochemical process. Presence of sulfur compounds in crude oil and creation a corrosive environment for steel structure, caused failure and unfortunate damages. H2S which present at cracking and sweetening process in sour feed obtain hydrogen atoms that can diffuse into steel structure which involve with its instruments and consequent to hydrogen damage .distribution and storage of these sour environments can be done by high strength low alloy steel (HSLA).Electrochemical hydrogen permeation test were performed to measure the hydrogen permeation current through A106/GR B pipeline steel in the electrolytes simulating... 

In this project sulfur concretes were prepared. The optimum of casting temperature, weight percent of sulfur cement and weight percent of filler were analyzed, so that better corrosion resistance could be found. It is observed, the optimum sulfur is 15% for sulfur concrete samples with 21% sulfur cement; the optimum filler is 10-15% with 18% sulfur cement and finally the optimum filler is 10% for concrete samples with 15% sulfur cement. The casting temperature for concrete with 15-21% sulfur cement is in the interval of 127-150°C could be achieved. By applying the relation between the optimum filler percent and the content of sulfur cement and choosing a suitable temperature for casting... 

Ni-Co/SiC composite coatings with various contents of SiC nano particles were electrodeposited in a modified watt type of Ni-Co bath containing 20 nm SiC nano particles to be codeposited. The influences of the SiC concentration, current density, stirring rate of the deposition bath on the composition of the coatings were investigated and these parameters optimized for highest amount of SiC codeposition. The optimized deposition parameters were 40 g/l SiC and 480 rpm stirring rate and current density equal to 4 A/dm2. Ni-Co/SiC composite coating was deposited with the maximum particles content of 30.5 volume percent. Linear voltammetry demonstrates addition of the SiC to the Ni-Co deposition... 

This research describes a new and relatively general method to grow well-aligned carbon nanotubes (CNTs) on cobalt-deposited stainless steel by thermal chemical vapor deposition (CVD) of ethylenediamine precursor. The CNTs are vertically aligned at high density over large areas on the surface. Different effective parameters in growth of carbon nanotubes, as type of substrate, surface treatment, temperature of growth , feeding carbon supplies have been studied. Finally, aligned carbon nanotubes have been prepared by 100-150 nm diameter and 9µ length. CoOx•nH2O–MWCNTs nanocomposites were successfully synthesized, using a cathodic electrochemical reduction of H2O2 to deposit cobalt... 

Detection and determination of ultra-trace electroactive materials using electrochemical methods have been widely employed by researchers since they offer a fast, easy and reliable approach. In this way, developing of new nanoelectrodes with special and unique properties plays a profound role on the achievement of better results.
Gold nanoelectrode ensembles are one of the most important nanoelectrodes which due to the high surface area, chemical, electrochemical and physical stability, and integration of a large number of individual nanoelectrodes, introduce excellent opportunities to be employed as promising nanoelectrodes in determinations applications.
In this work, preparation... 

In this research we focus on study and fabrication of ordered nanotube arrays of titanium oxide and their applications in photoelectrochemical cell. Nanotubular films of titanium oxide have been fabricated using anodization method. Short-length nanotubes, less than one micrometer, have been synthesized in aqueous electrolyte containing deionized water, hydrofluoric acid and phosphoric acid. To get Micron-length nanotubes, we have employed organic electrolyte containing ethylene glycol, deionized water and fluoride ammonium. After fabrication, the photo-catalytic activity of nanotubular structures was evaluated by measuring the rate of degradation of in methylene blue aqueous solution. The... 

In this project Ni-SiC nanocomposite coatings were electrodeposited using Watts nickel bath with addition of SiC particles to the bath. Optimization of Ni-SiC electrodeposition parameters was done using Response Surface Methodology (RSM). At specific conditions, 67 Vol% of 10nm SiC is incorporated in nickel electrodeposits which is unique and not yet reported. Study nanomechanical properties of these coatings using Nanoindentation method, it was realized that the dislocation density is increased as force increasing which is in agreement with increasing intensity of (220) and (200) reflections and intensity attenuation of (111) reflection. Nanoscratch tests show that these... 

In order to prevent electrostatic attraction on non-conductive surfaces, the most practical solution is to put antistatic coatings to reduce surface resistance. Nano tin oxide coatings are designed to produce surfaces with antistatic properties in the resistance range of 108-1012 Ω/cm. In this project, using a simple method, low temperature, without heat treatment and without the use of additive (dopant), tin oxide films with antistatic property were placed on the glass. Further, in order to obtain a coating with a suitable morphology and structure to increase the surface conductivity, the synthesis of tin oxide using the sol-gel method at ambient temperature was used. And to place the... 

Intumescent paints are coatings designed for passive fire protection of steel and other materials. In this research, the performance of water-based intumescent coating with vinyl acetate resin for cellulose fire conditions and epoxy-based coatings for hydrocarbon fire conditions has been investigated. The fire resistance of coatings was evaluated according to the ASTM E119 standard for water-based coating and UL1709 standard for epoxy-based intumescent coating. For the water-based intumescent coating, the expansion of char was investigated in a furnace with a temperature of 800°C for 1 hour. Thermal decomposition was studied by thermogravimetric analysis (TGA). Also, flammability was...