Sharif Digital Repository

The dissolution of plasma-sprayed hydroxyapatite (PHA) coatings with different characteristics, produced by various spraying conditions, in a Tris-buffered solution at pH 7.4 was experimentally studied through the measurement of the release of calcium ions. The phase composition of the coatings at surface and interface, and the porosity were evaluated. The analytical modeling revealed that the calcium dissolution process was composed of two stages. The first stage was found to be both surface and diffusion controlled. The second stage was an exactly diffusion-controlled dissolution. In the first stage, the rate of dissolution and the solubility of the coatings with minimum contents of... 

Ni-base superalloy René 80 is widely used in manufacturing aircraft turbine blades. The service temperature of this alloy is in the range of 760-982 °C. Although this alloy possesses suitable mechanical, oxidation and hot corrosion properties, it is coated in order to increase its wear, oxidation, erosion and hot corrosion properties against harmful environmental service conditions. In this paper the influence of applying diffusion coating (CODEP-B) on the tensile properties of René 80 has been studied in the temperature range of 22-982 °C. Experimental results show that the tensile properties of the coated specimens are relatively lower than that of uncoated ones in the same conditions. But... 

A headspace solid-phase microextraction (HS-SPME) method was developed for the trace determination of geosmin in water and apple juice samples. A poly(dimethylsiloxane) (PDMS) fiber was synthesized as coated fiber using sol-gel methodology. After performing the extraction in the headspace, the fiber was introduced directly into the injection port of a gas chromatography-mass spectrometry (GC-MS) using electron impact (EI) ionization mode. One-at-the-time optimization strategy was applied to investigate and optimize important extraction parameters such as extraction temperature and time, ionic strength, headspace volume, and desorption temperature and time. The analytical data exhibited an... 

In this article design and operation of a plastic optical fiber (POF) sensor based on the unconventional light leakage from one fiber to another one causing intensity modulation are presented. The dominant loss mechanism was found to be the evanescent loss and based on this phenomenon the optical fiber sensor was designed. The penetration depth of evanescent wave as a function of different refractive index of cladding was calculated. Operation of this sensor was tested as a liquid level sensor for different liquids and the experimental results are compared. The dry (air interface layer) and wet output (liquid interface layer) signals for this probe were measured for a series of measurements... 

The formation of macroporous bioactive hydroxyapatite(HA) coatings using polytetrafluoroethylene(PTFE) particles were studied. The porous HA coatings were prepared onto a pure titanium substrate by electrophoretic deposition(EPD) at 120 V for 1.5 min using ethanol suspensions mixture of HA (500 nm in size) and PTFE (1-3 μm in size) particles. Subsequently, the composite coatings obtained by EPD were heated at 900 °C for 60 min to disintegrate the organic PTFE particles and sinter the inorganic HA particles. The calcinations of the PTFE led to the formation of porosity in the HA coating. These results demonstrate a new method for creating porous HA coatings on titanium. © 2006 Elsevier B.V.... 

Apatite-coated Ag/AgBr/TiO2 was prepared by deposition of Ag as novel metal to generate electron-hole pairs by extending the excitation wavelength to the visible-light region, AgBr, and hydroxy apatite as photosensitive material and adsorption bioceramic, respectively. The energy dispersive X-ray spectrometry clearly showed the presence of Ti, Ag, Ca, and P elements on the surface of catalyst. The bactericidal experiments in dark media indicated that only the novel catalyst shows inhibiting growth of bacteria in this case. A transmission electron microscopy image illustrated that catalyst nanoparticles adhere to the outer membrane of the cell and act as an inhibitor to the nourishment of... 

Titania was deposited on glass fibers with a partial epoxy layer coating from a solution containing TiO2 nanoparticles at T = 90°C, and the adsorption process was examined by X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), Fourier transform infrared (FT-IR) spectroscopy, and photocatalytic activity measurements. XPS data demonstrated that about 25% of the surface was covered with TiO2 nanoparticles, with 10% on the epoxy layer and 15% on the glass body. It was found that TiO2 nanoparticles can be readily adsorbed on epoxy groups, whereas they have a low tendency to adsorb on carbon polymer chains. This difference can be... 

An integrated microsampling approach based on solid-phase microextraction (SPME) was developed to provide a complete solution to highly efficient and accurate pharmacokinetic studies. The microsampling system included SPME probes that are made of poly(ethylene glycol) (PEG) and C18-bonded silica, a fast and efficient sampling strategy with accurate kinetic calibration, and a high-throughput desorption device based on a modified 96-well plate. The sampling system greatly improved the quantitative capability of SPME in two ways. First, the use of the C18-bonded silica/PEG fibers minimized the competition effect from analogues of the target analytes in a complicated sample matrix such as blood... 

A fiber coating from polyaniline (PANI) was electrochemically prepared and employed for solid phase microextraction (SPME) of some polycyclic aromatic hydrocarbons (PAHs) from water samples. The PANI film was directly electrodeposited on the platinum wire surface in sulfuric acid solution using cyclic voltammetry (CV) technique. The applicability of this coating was assessed employing a laboratory-made SPME device and gas chromatography with mass spectrometry (GC-MS) for the extraction of some PAHs from the headspace of aqueous samples. Application of wider potential range in CV led to a PANI with more stability against the temperature. The homogeneity and the porous surface structure of the... 

The determination of the thermo-mechanical stress field in and around a spherical/ cylindrical inhomogeneity surrounded by a functionally graded (FG) coating, which in turn is embedded in an infinite medium, is of interest. The present work, in the frame work of Boussinesq/Papkovich-Neuber displacement potentials method, discovers the potential functions by which not only the relevant boundary value problems (BVPs) in the literature, but also the more complex problem of the coated inhomogeneities with FG coating and sliding interfaces can be treated in a unified manner. The thermo-elastic fields pertinent to the inhomogeneities with multiple homogeneous coatings and various combinations of... 

An exact thermoelasticity solution for a two-dimensional thick composite consisting of homogeneous and functionally graded layers is presented. The thermomechanical properties of functionally graded layers are assumed to vary exponentially through the thickness while the Poisson's ratio is taken to be constant. The heat transfer problem is solved under steady state condition accounting for the heat convection. Utilizing the stress function the governing equation reduces to a fourth order inhomogeneous partial differential equation which is solved exactly using Fourier series method. A comparative study is done between two sandwich structures with homogeneous and functionally graded coatings,... 

The influence of annealing temperature on the hydrophilic property of WO3 thin films deposited by thermal evaporation and sol-gel dip-coating methods was studied and compared for the first time. The thermal evaporated WO3 thin films annealed at 400 °C showed a nearly super-hydrophilic property without UV and visible illumination. By analysing the O(1s) core level peak of XPS spectra, the amount of oxygen contributed at various bonds (including O2-, OH- and H2O) on the surface of the annealed samples at different temperatures were measured. In addition, a correlation between the hydrophilicity and the concentration of chemisorbed water on the film surface was suggested, independent of the... 

By virtue of a method of displacement potentials, an analytical treatment of the response of a transversely isotropic substrate-coating system subjected to axisymmetric time-harmonic excitations is presented. In determination of the corresponding elastic fields, infinite line integrals with singular complex kernels are encountered. Branch points, cuts, and poles along the path of integration are accounted for exactly, and the physical phenomena pertinent to wave propagation in the medium are also highlighted. For evaluation of the integrals at the singular points, an accurate analytical residual theory is presented. Comparisons with the existing numerical solutions for a two-layered... 

The on-fiber standardization technique for solid-coated solid-phase microextraction (SPME) was studied, and a theoretical model is proposed for the isotropic behavior of adsorption and desorption, based on Fick's law of diffusion and the Langmuir model. The isotropy of the adsorption and desorption of analytes onto and from the surface of porous solid SPME fiber was validated with the use of a commercially available fiber, a 50-μm Carbowax/ templated resin for carbamate pesticide analysis in various sample matrixes, and a self-made polypyrrole fiber for diazepam analysis in blood samples. Time constants were comparable for the adsorption and desorption processes. Equilibrium constants and... 

This article presents the research results on production and performance of palladium-only catalytic converters. Monolith is used as catalyst carrier and gamma alumina as substrate. Dipping method is used for monolith washcoating. Palladium as the active metal is impregnated on gamma alumina using wet impregnation to produce catalyst samples. The effects of factors such as percent solid in slurry, milling time, calcination time and temperature, pH and existence of Al(NO3)3 on wash-coat characteristics were studied experimentally. SEM, XRD, and BET tests were carried out on the samples. Catalyst performance was tested in an experimental reactor that was designed for this research. The results... 

A thin coating made of linear elastic functionally graded material (FGM) perfectly bonded to an elastic substrate is considered. This work which is of particular interest to tribological community is devoted to the determination of the thermal and mechanical stresses due to mixed normal and tangential Hertzian surface pressure. The thermomechanical properties of the FGM coating are assumed to vary exponentially through the thickness. Solutions for temperature rise and stresses are obtained by use of Fourier transform technique. The influences of coating thickness, Peclet number and friction coefficient on temperature rise and stresses in the FGM coating are investigated. Comparative studies... 

Electrochemical co-deposition approach was expanded to prepare composite bio-ceramic coating of hydroxyapatite (HA)/polyvinyl acetate on the surface of titanium. The role is to improve the bioactive and crystallization properties. The results of XRD, XPS, SEM and TEM characterization showed that by increasing amount of vinyl acetate in the composite bio-ceramic coating before and after immersing in the simulated body fluid (SBF), an oriented growth of HA planes on the (0 0 2) direction had been observed on titanium substrate. Also significant surface morphology changes were obtained  

Laser Powder Deposition technique is an advanced production method with many applications. Despite this fact, reliable and accurate control schemes have not yet fully developed for this method. This article presents method for in time identification of the process for modeling and adaptation of proper control strategy. ARMAX structure is chosen for system model. Recursive least square method and Kalman Filter methods are adopted for system identification, and their performance are compared. Experimental data was used for system identification, and proper filtering schemes are devised here for noise elimination and increased estimation results. It was concluded that although both methods... 

Improvements in sealing mechanism between the rotating and the stationary parts of a rurbomachine can extensively reduce the endwall leakage flow. In this regard, abradable seals are incorporated into compressor and turbine blade-tip region. In a gas turbine, equipped with abradable seals, tip of the rotor blade is designed to cut into the material coating of the casing and to form a close fitted circumferential groove for the movement of the blade tip. As a result, the resistance to the leakage flow in the tip gap region increases due to smaller tip clearances (available without any rub-induced damages). Minimizing the tip clearance size can lead to an increase in performance and stability.... 

A novel solid-phase microextraction (SPME) method was developed for isolation of dextromethorphan (DM) and its main metabolite dextrorphan (DP) from human plasma followed by GC-MS determination. Three different polymers, poly(dimethylsiloxane) (PDMS), poly(ethylenepropyleneglycol) monobutyl ether (Ucon) and polyethylene glycol (PEG) were synthesized as coated fibers using sol-gel methodologies. DP was converted to its acetyl-derivative prior to extraction and subsequent determination. The porosity of coated fibers was examined by SEM technique. Effects of different parameters such as fiber coating type, extraction mode, agitation method, sample volume, extraction time, and desorption...