Sharif Digital Repository

The behavior of hot extruded Al-6Mg during hot deformation has been studied using hot compression test. The tests were performed at temperatures of 350, 450, and 550°C and strain rates of 0.001, 0.1, and 1s -1. Due to the effects of friction and adiabatic heating generated during compression, the attained true stress-true strain curves have been corrected. After correction of friction effect, the virtual work hardening has been removed from stress-strain curves. The flow stress increases and reaches a steady state after correction of adiabatic heating effect. Corrected curves and microstructural examinations exhibit the occurrence of dynamic recovery during hot compression of the alloy. The... 

The present paper reports the effects of Nd:YAG laser welding on the microstructure, phase transformation, cyclic deformation behavior, and corrosion resistance of Ti-55 wt.% Ni wire. The results showed that the laser welding altered the microstructure of the weld metal which mainly composed of columnar dendrites grown epitaxially from the fusion line. DSC results indicated that the onset of the transformation temperatures of the weld metal differed from that of the base metal. Cyclic stress-strain behavior of laser-welded NiTi wire was comparable to the as-received material; while a little reduction in the pseudo-elastic property was noted. The weld metal exhibited higher corrosion... 

Ultrafine-grained (UFG) Al6063 matrix nanocomposites reinforced with nano-size Al2O3 were produced by reactive mechanical alloying and hot powder extrusion method. Microstructural studies were performed by transmission electron microscope (TEM) and electron backscatter diffraction (EBSD). Observation of very small regions with high- and low-angle grain misorientation, i.e. grains and subgrains, showed the formation of UFG Al alloy matrix with an average grain size of ~ 0.37 μm. A uniform distribution of alumina particles with an average size of ~ 100 nm was also achieved. Compression test at various temperatures up to 450 °C was carried out to evaluate the high-temperature strength and hot... 

Polystyrene- (Styrene Ethylene Butylene Styrene-Maleic Anhydride) (SEBS-MA) composites with/without organoclay were prepared by melt intercalation method. The morphology, tensile and impact properties and deformation mechanism of these compounds were investigated. X-ray diffraction, transmission electron microscopy and reflected and transmitted optical microscopy techniques were used to study the morphology and deformation mechanisms. The results show that incorporation of SEBS with/without organoclay notably affects morphology, mechanical properties and plastic deformation of polystyrene. Introduction of SEBS with/without organoclay can facilitate initiation and growth of crazing mechanism... 

Flow stress behavior of AA5086 was determined using tensile testing at different temperatures from room temperature to 500 °C and strain rates varying between 0.002 and 1 s−1. The strain rate sensitivity parameter and occurrence of dynamic strain aging were then investigated in which an Arrhenius-type model was employed to study the serrated flow. Additionally, hot deformation behavior at temperatures higher than 320 °C was evaluated utilizing hyperbolic-sine constitutive equation. Finally, a feed forward artificial neural network model with back propagation learning algorithm was proposed to predict flow stress for all deformation conditions. The results demonstrated that the strain rate... 

In precipitation hardenable materials, it is desirable to determine the precipitate dissolution temperature for homogenizing the microstructure by controlling the size and distribution of the precipitates. In this research, the influence of various heat treatment and hot deformation conditions on the kinetics of γ ′ dissolution and its morphological evolution in Nimonic 115 was studied. In addition, hot deformation behavior of the material was investigated using hot compression experiments at varying temperature (between 1,050°C and 1,175°C) and strain rates (between 0.01 and 1 s-1) up to a true strain of 0.8. The values obtained for the solvus temperature of γ ′ precipitates by two methods... 

The effects of initial heat treatments, i.e. solution treating and over ageing, on deformation behavior of an age hardenable Al-Cu-Mg alloy, including mechanical properties and texture evolution, during multi-directional forging (MDF) are investigated. Hardness measurements, electron back scatter diffraction (EBSD) maps, and differential scanning calorimetry (DSC) are carried out. Mechanical behaviors of the alloy in terms of compressive stress and hardness test after MDF are investigated. In both solution treated and over-aged alloys, the compressive stress during MDF shows an increase up to the second pass, and by further straining the flow stress is decreased. However, shear and... 

A general flow line model is developed to investigate the deformation behavior of Cu and Al through Bc route of Equal Channel Angular Pressing process at curved and sharp dies. Considering the Taylor theory, the obtained strain and strain rate from the flow line model and also using a modified version of ETMB model, the evolutions of nano-structure in the processed Cu and Al are predicted. Comparison between the modeling results and experimental data is carried out and a reasonable agreement is achieved. The results show that the deformation in the sharp die occurs in a narrow zone with higher strain rate than that in the curved die. Also, the cell size of the processed Cu is smaller than... 

Abstract: The hot deformation behavior of coarse-grained (CG), ultrafine-grained (UFG), and oxide dispersion-strengthened (ODS) AA6063 is experimentally recognized though carrying out compression tests at different temperatures (300–450 °C) and strain rates (0.01–1 s−1). Microstructural studies conducted by TEM and EBSD indicate that dynamic softening mechanisms including dynamic recovery and dynamic recrystallization become operative in all the investigated materials depending on the regime of deformation. Moreover, the high temperature flow behavior is considerably influenced by the initial grain structure and the presence of reinforcement particles. The constitutive and artificial neural... 

The deformation behavior of a 49.8 Ni-50.2 Ti (at pct) alloy was investigated using the hot compression test in the temperature range of 700 °C-1100 °C, and strain rate of 0.001 s-1 to 1 s-1. The hot tensile test of the alloy was also considered to assist explaining the related deformation mechanism within the same temperature range and the strain rate of 0.1 s-1. The processing map of the alloy was developed to evaluate the efficiency of hot deformation and to identify the instability regions of the flow. The peak efficiency of 24-28% was achieved at temperature range of 900 °C-1000 °C, and strain rates higher than 0.01 s -1 in the processing map. The hot ductility and the deformation... 

Uniaxial compression test at different temperatures [573 K to 723 K (300 °C to 450 °C)] and strain rates (0.01 to 1 s−1) was employed to study the hot deformation behavior of an ultrafine-grained (UFG) Al6063 alloy prepared by the powder metallurgy route. The UFG alloy with an average grain size of ~0.3 µm was prepared by mechanical milling of a gas-atomized aluminum alloy powder for 20 hours followed by hot powder extrusion at 723 K (450 °C). To elaborate the effect of grain size, the aluminum alloy powder was extruded without mechanical milling to attain a coarse-grained (CG) structure with an average grain size of about 2.2 µm. By employing the dynamic materials model, processing maps for... 

The influence of Cu addition on the hot deformation behavior of NiTi shape memory alloys was investigated using hot compression test. A series of alloys with different Cu contents of Ti50.4Ni49.6-xCux (x = 0, 3, 5, 7 at.%) were deformed under compression to a true strain of 0.7 at the temperature range of 700-1000 °C with 100 °C intervals and constant strain rate of 0.1 s-1. The stress-strain curves showed that the addition of Cu to NiTi alloy made the flow curves shift upward. This was confirmed by the calculated critical stress, σc, obtained from inflections in θ-σ plots, which is attributed to the formation of high strength Cu containing precipitates and solid solution hardening caused by... 

Hot deformation behavior of Al6063 alloy produced by direct powder extrusion was studied by means of uniaxial compression test in the temperature range between 300 and 450°C and strain rate range between 0.01 and 1s -1. Electron backscatter diffraction (EBSD) technique and transmission electron microscopy (TEM) were utilized to study the microstructure of the material before and after the hot deformation. The microstructure of the extruded alloy consisted of elongated grains within a subgrain structure and small grains free of low angle grain boundaries (LAGBs). An equiaxed duplex microstructure consisting of large substructured grains and fine grains separated by high angle grain boundaries...