Sharif Digital Repository

Implementation of new materials in automotive body-in-white requires through knowledge of their metallurgical response to welding process thermal cycle. This two-part paper aims at understanding the physical and mechanical metallurgy of stainless steels, as interesting candidates for automotive application, during resistance spot welding. The second part addresses the phase transformations in the heat affected zone of three types of stainless steels including austenitic, ferritic and duplex steels. Failure modes and mechanical properties of stainless steel resistance spot welds are discussed. The peak load and energy absorption of stainless steel resistance spot welds are compared with... 

Weldability is one of the key requirements for automotive materials. This two-part paper aims at understanding the metallurgical phenomena during resistance spot welding of stainless steels, as interesting candidates for automotive body in white. Part I addresses the phase transformations in the fusion zone of three types of stainless steels including austenitic, ferritic and duplex types. The solidification and solid state phenomena including columnar to equiaxed transition, ferrite– austenite post-solidification transformation, martensitic transformation and carbide precipitation are discussed. Particular attention is given to the effect of high cooling rate of resistance spot welding... 

Titanium dioxide nanopowders were synthesized by the diffusion controlled sol-gel process (LaMer model) and characterized by DTA-TG, XRD, and SEM. The prepared TiO 2 nanoparticles have uniform size and morphology, and the phase transformation kinetics of obtained material was studied by interpretation of the X-ray diffraction patterns peaks on the base of Avrami equation. The stating point of anatase-rutile phase transformation temperature in the prepared nanoparticles was found between 100 and 200 C. A decreasing trend on the intensity of X-ray peaks of anatase phase was observed up to 600 C when the presence of the rutile phase became predominant. Results indicated that the transition... 

Recently, an increasing concern has been raised about turn-to-turn faults (TTFs) in power transformers, because these faults can lead to severe transformer insulation failure and consequently, its outage. Generally, it is impossible to experimentally analyze the transformer behavior under such faults, since the implementation of those experiments may be substantially destructive. Therefore, computer-aided models should be developed to investigate the performance of transformer protective relays under turn-to-turn faults. So far, existing transformer models are mainly formulated to implement in the EMTP-based softwares. However, most of power system protection engineers and researchers... 

The paper addresses the microstructure and failure characteristics of dissimilar resistance spot welds between austenitic stainless steel and ferritic stainless steel. The fusion zone (FZ) of dissimilar welds exhibited complex microstructure consisting of ferrite, austenite and martensite. The development of this triplex structure in the FZ was explained by analysing the phase transformation path and austenite stability. Results showed that all dissimilar welds failed in partial thickness-partial pull-out failure mode. It was shown that the fraction of the nugget fracture of the weld is reduced by increasing the FZ size improving the mechanical performance of the weld. Peak load and energy... 

Porous shape memory alloys are a class of very interesting materials exhibiting features typical of porous metals and of shape memory alloys. In contrast to dense shape memory alloys, considerable plastic strain accumulates in porous shape memory alloys even during phase transformation. Moreover, due to the microstructure of porous materials, phase transformation and plasticity phenomena are significantly pressure-dependent. In this article, we propose a three-dimensional phenomenological constitutive model for the thermomechanical behavior of porous shape memory alloys able to predict shape memory effect, pseudo-elastic behavior and plastic behavior under proportional as well as... 

A thermo-elastic analysis coupled with a phase change model is employed to evaluate thermal stresses as well as progress of austenite decomposition after hot strip rolling operations. The thermo-mechanical finite element analysis is utilized to assess the distributions of temperature and thermal stresses during cooling while at the same time, a model based on the additivity rule is used to determine the rate of austenite to ferrite decomposition. The proposed model is applicable to multi-pass rolling schedules while the effects of different process parameters including the rolling speed and cooling configuration of the run-out table can be taken into account. In order to verify the... 

This paper investigates the metallurgical and mechanical response of 2304 duplex stainless steel-as an interesting candidate for automotive body-in-white applications-to resistance spot welding. The results showed the high cooling rate associated with the resistance spot welding process suppressed the postsolidification ferrite-austenite transformation leading to improper ferrite-austenite phase balance with a reduced volume fraction of austenite and consequent precipitation of chromium-rich nitrides. The effects of welding current, as the key parameter determining the weld heat input, on the austenite volume fraction and precipitation are discussed. The minimum fusion zone hardness... 

This paper proposes a straightforward control method for voltage control of a three-phase transformer-based inverter in uninterruptible power supplies or distributed generation systems. The approach offers a dual-loop design consisting inner current control loop and outer voltage loop. Sliding mode current controller provides desired bandwidth for voltage controller which consists of a state feedback term for stabilization and resonant term for harmonic damping. The proposed scheme provides fast dynamic response and low total harmonic distortion even for high power inverters with the limitations of switching frequency and LC filter components. Experimental studies for 2KVA linear and... 

Recent uses of intelligent composites in biomedical appliances aggrandize the necessity of bonding-strength improvement in NiTi/silicone matrix interface. SEM micrographs and pull-out tests are employed to determine the strength of the NiTi/silicone bonds in a flexible composite piece. Greater adhesion strengths are obtained due to the presence of thin oxide layer, surface roughness and frictional forces between the embedded-wires and the contacting phase. Effect of curing treatment on phase transformation temperatures of the wires is determined by electrical resistivity (ER) measurements. Results show that the curing treatment shifts the transition points of the wires towards higher... 

Biphase TiO2 nanoparticles have been prepared by sol-gel method. Water/titanium molar ratio (r) has been used to control the hydrolysis and condensation of titanium isopropoxide in solution producing titanium oxide with two different polymorphs. The influence of crystallite size and morphology of prepared TiO2 on the phase transformation of the resultant materials has been investigated. Synthesized powders were characterized by X-ray diffraction, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Different trends can be observed in the phase transformation and particle growth of the prepared titanium oxide nanomaterial. It was concluded that, the rate of particle... 

This paper addresses the phase transformations and mechanical performance of dissimilar resistance spot welds between 2304 duplex stainless steel (DSS) and 1.2-GPa martensitic (MS) advanced high-strength steel (AHSS). The solidification mode and transformation path of the fusion zone (FZ) were analyzed. The key metallurgical feature of the FZ was the formation of a duplex microstructure consisting of delta ferrite and martensite. The FZ size at the sheet/sheet interface was the critical factor controlling the fraction of pullout failure during the partial thickness-partial pullout mode, the load-bearing capacity, and the energy absorption capability of the DSS/MS dissimilar resistance spot... 

The α-FAPbI3 perovskite nanocrystals exhibit interesting optical properties, which make them attractive for versatile optoelectronic applications; however, the spontaneous phase transformation to the non-perovskite phase (δ-FAPbI3) in humid conditions requires a new strategy to improve the phase stability of the material. We employed 3-Aminopropyl triethoxysilane (APTES)-assisted reprecipitation and sol-gel methods at ambient temperature to prepare stable α-FAPbI3 nanocrystals embedded in a silica matrix. Transmission electron microscopy (TEM) and X-ray diffraction analysis determined that ultrafine perovskite nanocrystals (11.5 ± 3 nm) were uniformly distributed in a silica matrix.... 

The microstructure evaluation and phase transformation of multi-pass friction stir-processed (FSP) commercially pure titanium were investigated using optical microscopy, scanning electron microscopy equipped with a backscatter detector, and electron backscatter diffractometer. The microstructure characterization shows that the grain refinement mechanism changed with the increasing number of passes. The equiaxed α grains in the untreated sample changed to lath-shaped grains surrounded by serrated grain boundaries, and produced Widmanstätten morphology during the cooling cycle of FSP. The higher micro-hardness values and bio-corrosion resistances of the FSP-treated samples are due to their... 

Abstract: Nickel–titanium (NiTi) nanoparticles are ultrafine smart materials manifesting shape memory effect at very small scales. We have produced NiTi nanoparticles surrounded by an amorphous carbon shell using an innovative spark discharge system. The resulting nanoparticles were studied using various characterization methods to systematically study their size, morphology, size distribution, composition, structure, and thermal behavior. Field-emission scanning electron microscopy and dynamic light-scattering results indicated that the average size of the produced nanoparticles was about 13 nm. High-resolution transmission electron microscopy, energy-dispersive spectroscopy (EDS), and... 

Highly stable, water-based barium titanate (BaTiO3) sols were developed by a low cost and straightforward sol-gel process. Nanocrystalline barium titanate thin films and powders with various Ba:Ti atomic ratios were produced from the aqueous sols. The prepared sols had a narrow particle size distribution in the range 21-23 nm and they were stable over 5 months. X-ray diffraction pattern revealed that powders contained mixture of hexagonal- or perovskite-BaTiO3 as well as a trace of Ba2Ti 13O22 and Ba4Ti2O27 phases, depending on annealing temperature and Ba:Ti atomic ratio. Highly pure barium titanate with cubic perovskite structure achieved with Ba:Ti = 50:50 atomic ratio at the high... 

CeO 2-TiO 2 nanoparticles were prepared by the sol-gel process using 2-hydroxylethylammonium formate as room-temperature ionic liquid and calcined at different temperatures (500-700°C). CeO 2-TiO 2-graphene nanocomposites were prepared by hydrothermal reaction of graphene oxide with CeO 2-TiO 2 nanoparticles in aqueous solution of ethanol. The photocatalysts were characterized by X-ray diffraction, BET surface area, diffuse reflectance spectroscopy, scanning electron microscopy, and Fourier transformed infrared techniques. The results demonstrate that the room-temperature ionic liquid inhibits the anatase-rutile phase transformation. This effect was promoted by addition of CeO 2 to TiO 2....