Sharif Digital Repository

Wettability is one of the most important factors which significantly influences solar still efficiency. Moreover, it determines the condensation mode, i.e., filmwise or dropwise condensation. In the present study, materials with different wettability were applied as the condensing surface to evaluate the effect of wettability on the distillate production of a single slope solar still. To compare the effects of dropwise and filmwise condensation on the condensate yield, the wettability of the condensing surface was changed by applying a nano-silicon solution according to a dip coating technique. All the experiments were conducted at three surface inclination angles. The results revealed that... 

The bacterial strain MJ01 was isolated from stock tank water of one of the Iranian south oil field production facilities. The 16S rRNA gene of isolate, MJ01, showed 99% similarity to Bacillus subtilis. The results revealed that biosurfactant produced by this strain was lipopeptide-like surfactin based on FTIR analysis. Critical micelle concentration of produced surfactin in distilled water was 0.06 g/l. Wettability study showed that at zero salinity surfactin can change original oil-wet state to water-wet state, but in seawater salinity it cannot modify the wettability significantly. To utilize this biosurfactant in ex situ MEOR process, economical and reservoir engineering technical... 

Capillary imbibition is an important recovery mechanism in naturally fractured reservoirs when water-filled fractures surround water-wet matrix blocks. A large amount of studies of imbibition process is simply total or partial immersion of nonwetting phase saturated rock in aqueous wetting phase. However, water advance in fractures during water flooding or water encroachment from an active aquifer introduces time dependent boundary conditions where invariant exposure of rock surface to water is not representative. In this work, a laboratory simulated matrix-fracture system was used to investigate different aspects of imbibition in the presence of fracture fluid flow (namely dynamic... 

An existing hydroelastic model is extended for a flat plate subjected to a compression force with spiral spring boundary conditions during water entry. Both vertical and oblique impacts of the plate into calm water are investigated. A longitudinal strip of the plate is analyzed by fully coupling hydrodynamic pressure with elastic responses. Hydrodynamic pressure is determined by potential flow theory and plate deflections are expressed in terms of dry normal modes. The plate deflections are validated through comparison with available asymptotic models, semi-analytical and experimental results. The effect of compression force on the plate deflection is investigated at the midpoint considering... 

In this work, application of silica nanoparticles for wettability alteration of initially oil-wet calcite was investigated through analysis of surface forces and DLVO theory. Doing so, the wettability and zeta potential of calcite surfaces were measured through the sessile drop method and an in-house experimental setup, respectively. Primary evaluation indicated that incorporating DLVO terms in the Frumkin-Derjaguin model was not sufficient to describe the wettability in an oil-wet calcite/nanofluid system. Sensitivity analysis showed that calculating the double-layer interaction using constant potential-constant potential boundaries along with structural hydrophobic forces (non-DLVO... 

Three-dimensional (3D) polyamide scaffolds were fabricated by applying a solvent bath as the collecting element. Electrospun nanofibers were immersed into the solvent bath to give a material with a laminated 3D texture. In parallel, 2D nanofibers were synthesized and utilized as microextractive phases in a needle trap device to compare the capabilities of 2D and 3D materials in terms of headspace extraction of various chlorobenzenes (chlorobenzene, 1,2-dichlorobenzene, 1,4-dichlorobenzene, 1,2,4-trichlorobenzene and 1,2,3,4-tetrachlorobenzene). The results demonstrate the superiority of 3D nanofibrous scaffolds over 2D mats. The porosity, morphology, and thermal stability of the 3D scaffolds... 

Although several investigations have studied the low-salinity water injection (LSWI) performance during the past decades, the effect of crude oil type on the interfacial tension (IFT) and wettability alteration is still in dark. In this regard, this study is aimed to obtain the thermodynamic energies including adhesion, cohesion and spreading coefficient during LSWI. To achieve this goal, IFT and static contact angle values of three different crude oils (i.e. light, medium and heavy) are measured as a function of sea water salinity. The obtained results revealed that the dilution of sea water can change the wettability of reservoir rock from oil wet state towards water wet state, while crude... 

This research investigated the long-term environmental effects on the bond at the interface between fiber-reinforced polymer (FRP) and a masonry brick. Seven types of FRP fabrics were used and placed on the masonry brick using the wet lay-up technique. Unidirectional and bidirectional fibers made of aramid, carbon, and glass and also combination of these fabrics were used. A total of 525 specimens were exposed to five chemical solutions with pH values of 2.5, 7, 10, 12.5 and substitution sea water for 1, 3, 6, 9 and 12 months. A chamber was also used to simulate the ultraviolent (UV) radiation on the specimens. A series of single-lap shear tests were performed on these specimens to determine... 

In this study, four types of mixed matrix membranes were fabricated using polysulfone (as the base polymer) and different contents of graphene oxide (GO) nanosheets (as modifier) through wet phase inversion method. Based on the amounts of GO (0, 0.5, 1, and 2 wt%), the synthesized membranes named as M1, M2, M3, and M4, respectively. The membranes characteristics were evaluated using FE-SEM, FT-IR, and water contact angle measurements. In addition, the performance of the prepared membranes was investigated in terms of basic parameters: filtrate water flux, nitrate removal efficiency, and antifouling properties. Results showed significant improvements of the characteristics of modified... 

The high reactivity of the carbonate rocks at various pH makes it difficult to evaluate the wettability, hence to find the recovery mechanisms behind modified waterflood in carbonate reservoirs. More recently, the streaming potential measurement is introduced as a method of electrokinetic phenomena more relevant to the subsurface systems. Regarding few experimental studies and in order to improve our understanding on streaming potential measurement, the electrokinetic studies on quartz and calcite surface were conducted as a function of pH in the range of 1.5–11.5 using an in-house novel setup of streaming potential measurement. High sensitivity of streaming potential coupling coefficient to... 

Acidizing of carbonate oil-wet rocks saturated with oil and saline formation water is subjected failure in some cases due to acid-induced damage such as sludge and emulsion formations. This condition may also lead to mineral precipitation, oil film barrier between acid and rock and diversion chemical malfunctions. Therefore, pre-flush process has been proposed as one of the most efficient stage for oil-wells matrix acidizing to reduce these challenges significantly. Besides, the pre-flush stage would result in more clean rock as the reservoir fluids are pushed back from the near wellbore regions, restoring rock wettability to more water wet state, preventing direct acid-oil contact and... 

Current available models for simulation of the separation process in gas-liquid membrane contactor (MC) systems consider a uniform partial membrane wetting along the membrane length (Lmem). However, transmembrane pressure changes along the Lmem. Additionally, the available models usually consider a simplified uniform pore size to represent the micro-porous MC. Additionally, not all pores in a MC have the same size. In this study, a pore-scale network model is developed to simulate the physical separation of H2S using MCs by taking to account for (i) transmembrane pressure variation and (ii) pore size distribution of MC. The model results are compared with the experimental results of H2S... 

Productivity of gas condensate reservoirs reduces significantly due to the near wellbore condensate/water blockage phenomenon. A novel, permanent solution to alleviate this problem is near wellbore wettability alteration of reservoir rocks to preferentially gas wetting conditions; industrial chemical materials are good candidates for this purpose, because of their eco-friendly characteristics, economical price, and mass production. In this paper, a comparative study is conducted on two industrial fluorinated chemicals, MariSeal 800 and SurfaPore M. Static and dynamic contact angle measurements, spontaneous imbibition, and core flooding tests were conducted to investigate the effect of... 

Accurate determination of relative permeability (kr) curves and their hysteresis is needed for reliable prediction of the performance of oil and gas reservoirs. A few options (e.g., Carlson, Killough and Jargon models) are available in commercial reservoir simulators to account for hysteresis in kr curves under two-phase flow. Two-phase kr curves are also needed for estimating kr hysteresis under three-phase flow during water-alternating-gas (WAG) injection. Although, most oil reservoirs are mixed-wet, the existing hysteresis predictive approaches have been developed based on water-wet conditions. Experimentally measured data are needed to assess the performance of these methodologies under... 

In the current study, a novel approach which takes into account the effectiveness of both convectional surfactants and biosurfactants was investigated. The biosurfactant produced by Enterobacter cloacae strain was utilized concomitant with conventional surfactant (sodium dodecyl benzene sulfonate (SDBS)) to evaluate its capability to reduce the SDBS adsorption on rock surface (biosurfactant acts as sacrificial agent) or synergistically enhance the effectiveness of the SDBS. In this regard, the wettability alteration and interfacial tension (IFT) measurements and calculation of spreading coefficient were performed considering two different scenarios. In the first scenario, SDBS was added to... 

The results of previous studies on silt and clay indicated that variations in the small strain shear modulus, Gmax, during hydraulic hysteresis had a non-linear increasing trend with matric suction, with greater values upon wetting. However, due to differences in material properties and inter-particle forces, a different behavior is expected for the Gmax of unsaturated sand. Although considerable research has been devoted in recent years to characterizing the behavior of the Gmax of sand during drying, less attention has been paid to the effect of hydraulic hysteresis on Gmax and its variations during wetting. In the study presented herein, an effective stress-based semi-empirical model was... 

In this work, coupled Cahn–Hilliard phase field and Navier–Stokes equations were solved using finite element method to address the effects of micro-fracture and its characterizations on water-oil displacements in a heterogeneous porous medium. Sensitivity studies at a wide range of viscosity ratios (M) and capillary numbers (Ca), and the resultant log Ca–log M stability phase diagram, revealed that in both media, with/without fracture, the three regimes of viscous fingering, capillary fingering and stable displacement similarly occur. However, presence of the fracture caused water channeling phenomenon which resulted in reduction of the number of active fingers and hence the final oil... 

Low salinity (LS) and smart water (SW) flooding processes which receive a great interest as cost-effective and environmental friendly techniques are relatively new enhanced oil recovery methods. Although shifting carbonate surfaces towards a water-wet state is the main mechanism behind these methods, effects of controlling factors (for instance: ion type or salinity) are already remained unsettled. In this regard, the effects of sulfate ion types (i.e. Na2SO4, MgSO4 and CaSO4) and their concentrations (i.e. 0–45,000 ppm) on wettability alteration are investigated using contact angle (CA) measurement technique. In addition, work of cohesion, work of adhesion and spreading coefficient of all... 

Memristor devices have attracted tremendous interest due to different applications ranging from nonvolatile data storage to neuromorphic computing units. Exploring the role of surface roughness of the bottom electrode (BE)/active layer interface provides useful guidelines for the optimization of the memristor switching performance. This study focuses on the effect of surface roughness of the BE electrode on the switching characteristics of Au/TiO2/Au three-layer memristor devices. An optimized wet-etching treatment condition was found to modify the surface roughness of the Au BE where the measurement results indicate that the roughness of the Au BE is affected by both duration time and... 

Calcite is among the most abundant minerals organizing the oil reservoir formation and therefore its surface properties play a central role in the increase of the oil recovery efficiency. The effect of low-salinity water in carbonate rocks reveals that brine composition and salinity can improve the oil recovery in carbonates through wettability alteration. However, the specific mechanism for wettability changes that leads to improved oil recovery in calcite is not well understood. To obtain deeper insights at atomic level into the understanding the characteristics of the calcite-water interface, we performed classical molecular dynamics simulations in the presence of different ions in brine...