Sharif Digital Repository

Friction stir processing (FSP) can be used to improve surface composites. In this study, a modified method of FSP called friction stir vibration processing (FSVP) was applied to develop a surface composite on AZ91 magnesium alloy. In this technique, the workpiece is vibrated normal to the processing direction. The results illustrated that compared with the FSP method, the FSVP caused a better homogeneous distribution of SiC particles in the microstructure. The results also showed that matrix grains of friction stir vibration processed (FSV-processed) samples ((26.43 ± 2.00) µm) were finer than those of friction stir processed (FS-processed) specimens ((39.43 ± 2.00) µm). The results... 

In this study, evolution of intermetallic layer of the cold roll bonded bilayer of Aluminum-Steel sheets, during severe plastic deformation (SPD) followed by annealing has been investigated. The effect of such evolution on mechanical properties has been discussed. For this purpose, Constrained Groove Pressing (CGP) was used as a SPD process. Field emission scanning electron microscope equipped with energy dispersive spectroscopy and optical microscopy were used for examination of intermetallic compounds morphology and composition. Meanwhile, tensile properties of the bilayer sheets were evaluated. According to microstructural observations, continuous intermetallic layer was formed during... 

This research explored the influences of shielding gases on the appearance of weld beads and the microstructures and mechanical properties of thin-wall samples using conventional gas metal arc welding as the heat source by using 5356 aluminium alloy welding wire as the raw materials and nitrogen (N2) and argon (Ar) as the shielding gases. The results showed that under the same parameters and after mono-layer single-bead welding was performed using N2 as the shielding gas, the bead height was higher, the bead width was narrower, and the penetration depth was shallower. The grain size of the thin-wall sample protected by N2 was 43.5–47.8 % smaller than that obtained under Ar protection.... 

Effects of Fe particle volume percent (from 0 to 5%) and changing the tool rotation direction in each pass were studied on the microstructure evolution and mechanical properties of the in situ Al/intermetallic composites produced by three passes friction stir processing (FSP) with ∼10 µm Fe particles. Optical and scanning electron microscopes were used for the investigation of the composite homogeneity, formation of Al–Fe intermetallic compounds, and fracture surfaces. Tensile and microhardness tests were also carried out to evaluate the mechanical properties of the composites. Solid-state reactions between the aluminum matrix and Fe particles led to in situ formation of Al3Fe and Al5Fe2... 

Low-carbon steel sheets are severely plastic deformed to strains of up to ≈3.48 and subsequently heat treated by conventional annealing followed by water-quenching. Four temperatures are chosen for the annealing below and over the Ac1 and Ac3 transformation lines. The effects of post-deformation heat treatment are investigated by evaluating the microstructure and mechanical properties, including strength, ductility, work hardening capability, and hardness. A maximum increase of 86% in the strength is obtained through intercritical annealing and quenching of the samples subjected to strain of 1.16. It is interesting that both the elongation and ultimate tensile strength values are higher... 

This paper presents the creep behavior of various FRP (GFRP, CFRP, and hybrid) bars in order to investigate the effects of different parameters, including the applied stress levels, bar diameter, and the type of fiber and resin in the creep behavior of FRP bars. The creep strains versus time curves were experimentally obtained for 83 days. Moreover, a statistical study, including analysis of variance (ANOVA) and linear Bayesian regression was conducted to investigate the contribution of the studied parameters. The results showed that in GFRP bars the ratio of ultimate creep strain to the initial elastic strain decreased when the applied stresses on the bars exceeded 30% of their ultimate... 

The friction stir welding of AA2024-T6 to AA6061-T6 plates with a 4 mm thickness has been studied at constant traverse and rotational speeds of 1000 rpm and 100 mm/min, respectively. The position of alloys and the effects of precipitation hardening heat treatment in retreating and advancing side in the friction stir welding were analyzed. The tool with taper threaded pin was used for welding. Macro and microstructural analysis were investigated by using Optical and Field Emission-Scanning Electron Microscopes (FE-SEM) to check out the welded joints. Micro-hardness and Tensile tests were also done to study mechanical attributes of the joints. Microstructural analysis revealed some grain... 

Aluminum matrix in situ nanocomposite was produced by one to six passes friction stir processing (FSP) with pre-placed Fe3O4 nanoparticles (15-20 nm). Microstructure studies showed that solid-state reactions between the aluminum matrix and Fe3O4 particles during the process led to in situ formation of Al3Fe and Al5Fe2 in the stir zone. Initial Fe3O4 as well as Al-Fe intermetallic compounds (IMCs) particles were homogeneously dispersed in a fine grain matrix after six passes of FSP. Hardness and ultimate tensile strength of the composites were increased 64 and 27%, respectively, compared to the base metal. The reasons were studied in the light of reinforcing particles distribution, formation... 

Aluminum metal-matrix nanocomposites (AMMNCs) fabricated by conventional stir-casting process usually show high porosity and poor distribution of nanoparticles within the matrix. In the current study, for the improvement of nanoparticles distribution in the aluminum matrix and enhancement of the mechanical properties, a mixture of Al/nano-Al2O3 powders were injected by pure argon gas into the molten 7075 aluminum alloy and this mixture was extruded at high temperature. Mechanical behavior of the final product was investigated by tensile and compression tests, hardness measurements, Scanning Electron Microscopy (SEM), High Resolution Transmission Electron Microscopy (HRTEM) and Optical... 

Aluminum metal-matrix nanocomposites (AMMNCs) fabricated by conventional stir-casting process usually show high porosity and poor distribution of nanoparticles within the matrix. In the current study, for the improvement of nanoparticles distribution in the aluminum matrix and enhancement of the mechanical properties, a mixture of Al/nano-Al2O3 powders were injected by pure argon gas into the molten 7075 aluminum alloy and this mixture was extruded at high temperature. Mechanical behavior of the final product was investigated by tensile and compression tests, hardness measurements, Scanning Electron Microscopy (SEM), High Resolution Transmission Electron Microscopy (HRTEM) and Optical... 

In this research, Araldite 2011 has been reinforced using different weight fractions of Reduced Graphene Oxide (RGO). Fourier Transform Infrared Spectroscopy (FTIR), Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM) analyses were conducted and it has been shown that introduction of the RGO greatly changes the film morphology of the neat adhesive. Uni-axial tests were carried out to obtain the mechanical characteristics of the adhesive-RGO composites. It has been observed that introducing 0.5 wt% RGO enhances the ultimate tensile strength of the composites by 30%. In addition, single lap joints using neat adhesive and adhesive-RGO composites were fabricated to... 

The grain size of constrained groove pressed aluminum has been predicted through the genetic programming approach. “Sheet thickness,” “elongation,” “yield strength,” “ultimate tensile strength,” “total strain,” and “hardness,” along with “primary grain size” of the ultrafine-grained sheets were utilized as input parameters to obtain the ultimate grain size. A total number of 73 available data in the literature were gathered and randomly divided into 60 and 13 sets for algorithm training and testing, respectively. Among the presented models, the one with best performance utilized parameters of total strain, ultimate tensile strength, and primary grain size with 40 chromosomes, 10 head sizes,... 

Plates of AA5052 (Al-Mg) alloy in both annealed (solution-treated) and wrought (rolled) temper conditions were subjected to friction stir processing (FSP) at various w/. v pitch ratios from 4 to 28. rev.min/mm. The role of stored strain energy on the evolution of restoration mechanisms and crystallographic texture components were assessed in terms of microstructural features evaluated using electron back-scattered diffraction (EBSD) and transmission electron microscopy (TEM) analysis. The results revealed that FSP significantly refined the grain structure and changed the crystallographic micro-texture components. The grain size of the annealed and wrought alloy was reduced from 49.4 and 9.7.... 

In-situ aluminum matrix composites were fabricated by 1-3 passes of friction stir process (FSP) using iron (Fe) particles with initial size of 10. μm. Although the initial reinforcing particles were relatively large in size and also agglomerated particles were formed in the obtained composites, all of the processed specimens fractured from the base metal during transverse tensile test. Longitudinal tensile tests revealed that the ultimate tensile strength (UTS) of the composites was up to 43% higher than that of the base metal; however, the strain to fracture of the composites reached to about 0.2. Al-Fe intermetallic compounds (IMCs) formed at the interface of the aluminum matrix and Fe... 

This work was carried out to investigate the effect of different Ti concentrations as a modifying agent on the microstructure and tensile properties of an in-situ Al-15 pctMg2Si composite. Cast, modified, homogenized small ingots were extruded at 753 K (480°C) at the extrusion ratio of 18:1 and ram speed of 1 mm/s. Various techniques including metallography, tensile testing, scanning electron microscopy were used to characterize the mechanical behavior, microstructural observations, fracture mechanisms of this composite. The results showed that 0.5 pctTi addition and homogenizing treatment were highly effective in modifying Mg2Si particles. The results also exhibited that the addition of Ti... 

The unique properties of NiTi alloy, such as its shape memory effect, super-elasticity and biocompatibility, make it ideal material for various applications such as aerospace, micro-electronics and medical device. In order to meet the requirement of increasing applications, great attention has been given to joining of this material to itself and to other materials during past few years. Laser welding has been known as a suitable joining technique for NiTi shape memory alloy. Hence, in this work, a comparative study on laser welding of NiTi wire to itself and to AISI 304 austenitic stainless steel wire has been made. Microstructures, mechanical properties and fracture morphologies of the... 

The variation of morphology and mechanical properties of Al6061 automotive aluminum alloy due to friction stir welding (FSW) and gas tungsten arc welding (GTAW) was investigated by optical metallography, scanning electron microscopy, microhardness measurement, X-ray diffraction, tensile testing, and fractography. The center-line dendrite emergence and microhardness reduction in the heat-affected zone were observed in the GTAW process. Although similar microhardness reduction with respect to the base metal was observed in the FSW samples, higher HVs were obtained for the FSW rather than the GTAW process at almost all heat-affected locations. Ultimate tensile strengths of the FSW and the GTAW... 

Aluminium matrix composites reinforced with submicrometre and nanosize Al 2O 3 particles were successfully manufactured in the form of sheets through eight cycles of accumulative roll bonding process. The mechanical properties of the produced composite are compared with accumulative roll bonded commercially pure aluminium. It is shown that only 1 vol.-% of submicrometre or nanosize alumina particles as reinforcement in the structure can significantly improve the yield and ultimate tensile strengths. Scanning electron microscopy revealed that particles have a random and uniform distribution in the matrix especially in the less volume fraction of alumina particles, and strong mechanical... 

As one of the key technologies for high performance electronic devices, composite solders have been recently developed to improve thermal and mechanical properties of solder joints. In this study, accumulative roll bonding process was used as an effective alternative method for manufacturing high-strength, finely dispersed, void-free and highly uniform Sn-Ag-Cu/CeO 2 nanocomposite solders. Microstructural investigation of nanocomposite solders revealed that homogenous distribution of CeO 2 nanoparticle has been achieved and the eutectic as-cast morphology of the solder changed to recrystallized fine grained structure. As a result of severe plastic deformation during rolling, brittle and... 

AISI 4340 steel bars were heated at 900 °C for one hour, annealed at 738 °C for different durations and oil-quenched in order to obtain dual phase steels with different ferrite volume fractions. A 3% prestrain at the temperature range of 150-450 °C was then imposed to the samples, and room temperature tensile tests were carried out, afterwards. Results indicate that the maximum values for both yield and ultimate tensile strength would exist for the samples pre-strained at the temperature range of 250-300 °C. Also, a sudden drop of the ductility was observed at the mentioned temperature range. The observed behavior might be attributed to the occurrence of dynamic strain aging taken place at...