Sharif Digital Repository

In this work, the formability of a hybrid material of Interstitial-Free 240 (IF240) steel and AZ31 magnesium alloy as IF240/AZ31/IF240 tri-layered sheets was investigated. For this purpose, the bonding feasibility of the high-formability IF240 steel and low-formability AZ31 sheets was first assessed. Then, the hot formability behavior of the manufactured laminated composite was evaluated. The rolling of the preheated samples established the layer bonding. The bonding strength was determined using the shear punch test. The texture and its effects on the forming behavior were studied using the x-ray Goniometry method. Nakazima dome tests were employed at ambient and elevated temperatures to... 

The effect of pulsed direct current (PDC) on solid-state diffusion in the Ni–Al binary system was investigated. Two experimental schemes were employed: in the presence and absence of an electric field. The diffusion couples were heat-treated for 1.5, 3, and 5 h at 803, 833, and 863 K. Under the investigated conditions, only two intermetallic phases (NiAl3 and Ni2Al3) formed at the boundary of the metals. It was shown that the PDC passing through the diffusion couple significantly enhanced the growth rates of both phases. The apparent reaction–diffusion coefficients were DNiAl3=4.0×10−9exp(−[Formula presented]) and DNi2Al3=9.7×10−9exp(−[Formula presented]) in the field-assisted scheme,... 

ABSTRACTs: The need for fully dense material with well-engineered microstructures has led to the promising emergence of innovative sintering technologies among which the Spark Plasma Sintering (SPS) is one of the most favorite. Unlike the conventional sintering processes, SPS takes advantage of a current flow passing through the sintering die and metallic powders by which fast densification with minimal grain growth and enhanced physicomechanical properties can be obtained. Albeit there is a growing interest in the exploitation of SPS in producing sufficiently consolidated metallic parts, no analytical review has been released over the effects of SPS parameters on the densification behavior,... 

The MgO-supported Fe-Co-Mn catalysts, prepared using co-precipitation procedure, were tested for production of light olefins via CO hydrogenation reaction. The effect of a range of drying conditions including drying temperature and drying time on the structure and catalytic performance of Fe-Co-Mn/MgO catalyst for Fischer-Tropsch synthesis was investigated in a fixed bed micro-reactor under the same operational conditions of T = 350 °C, P = 1 bar, H2/CO = 2/1, and GHSV = 4500 h-1. It was found that the catalyst dried at 120 °C for 16 h has shown the best catalytic performance for CO hydrogenation. Furthermore, the effect of drying conditions on different surface reaction rates was also... 

High strength Al-AlN composites were synthesized via high-energy milling and sintering technique. Al-X wt.% AlN (X = 0, 2.5, 5 and 10) composite powders were milled in a planetary ball mill for 25 h. Morphology, particle size distribution, crystallite size, micro-strain, and microhardness of milled powders were studied. Ball-milled powders were degassed at 400 °C for 30 min. After uniaxial cold compaction, composite compacts were sintered at 650 °C for 20, 30 and 60 min under N2 atmosphere. Effects of reinforcement content, degassing treatment and sintering time on the sinterability of powders were investigated. The results revealed that the sinterability was degraded by increasing the... 

High-energy milling technique was used to synthesize Al-10 wt.%AlN-nanostructured composite powder in a planetary ball-mill under argon atmosphere up to 25 h. To show the role of AlN particles, process was conducted for monolithic aluminum. The changes in powder characteristics were investigated by time. Microstructure of powders was studied after different milling times by scanning electron microscope (SEM). The morphological evolutions showed that relative equiaxed powder could be synthesized after 25 h milling. Structural analysis was performed by X-ray diffraction method (XRD) to determine the grain sizes and lattice strain. Furthermore, particle size analysis (PSA) revealed the... 

Arrayed Ti6Al4V nanotubes (TNT) coated with hydroxyapatite (HA) were synthesized via electrochemical anodization method. Paracetamol was loaded onto TNT-HA electrode. Effects of anodization, nanotube formation and hydroxyapatite deposition on sorption and release of the drug were investigated. Saturation time of paracetamol on the anodized samples was 30% shorter than the hydroxyapatite-coated samples. Release behavior of the loaded drug was studied by (a) plunging the probe into phosphate buffered saline (PBS), (b) sampling the drug-loaded PBS at different times and (c) analyzing the solution via ultraviolet-visible (UV-vis) spectroscopy. Results showed that HA electrodes hold higher... 

The influence of different parameters such as welding pressure, rotational speed, and traverse speed on the weld properties has been evaluated earlier but there are some important parameters yet to be thoroughly investigated. In this study, an effort has been made to determine the influence of different ratios of rotational speed/traverse speed on mechanical properties of different zones of friction stir welded AZ31 magnesium alloy. Mechanical properties of different zones were determined by a shear punch test. It was found out that increasing the aforementioned ratio leads to a slight decrease in yield and ultimate strength of the stir zone and the transitional zone. It was also observed... 

In this research, the atomic scale local structures in (Zr0.5Cu0.5)100−xAlx (x = 0,2,4,6,8,10,12) bulk metallic glass was studied using molecular dynamics simulation method. The pair distribution function, Voronoi analysis and mean squared displacement (MSD) were adopted for investigation of the local structures. It was found that Cu- and Al-centered full icosahedra possess the most frequency accompanied by the most changes during the glass transition process in the supercooled liquid region temperature. Moreover, it was observed that the Al-centered full icosahedra (Al-FI) and Cu-centered full icosahedra (Cu-FI) clusters with 2.5% and 1.9% increase (relative to total atoms), respectively,... 

The solubility of Pd(NO3)2 in water is moderate whereas it is completely soluble in diluted HNO3 solution. Pd/MIL-101(Cr) and Pd/MIL-101-NH2(Cr) were synthesized by aqueous solution of Pd(NO3)2 and Pd(NO3)2 solution in dilute HNO3 and used for CO oxidation reaction. The catalysts synthesized with Pd(NO3)2 solution in dilute HNO3 showed lower activity. The aqueous solution of Pd(NO3)2 was used for synthesis of mono-metal Ni, Pd and bimetallic PdNi nanoparticles with various molar ratios supported on MOF. Pd70Ni30/MIL-101(Cr) catalyst showed higher activity than monometallic counterparts and Pd + Ni physical mixture due to the strong synergistic effect of PdNi nanoparticles, high distribution... 

The solubility of Pd(NO3)2 in water is moderate whereas it is completely soluble in diluted HNO3 solution. Pd/MIL-101(Cr) and Pd/MIL-101-NH2(Cr) were synthesized by aqueous solution of Pd(NO3)2 and Pd(NO3)2 solution in dilute HNO3 and used for CO oxidation reaction. The catalysts synthesized with Pd(NO3)2 solution in dilute HNO3 showed lower activity. The aqueous solution of Pd(NO3)2 was used for synthesis of mono-metal Ni, Pd and bimetallic PdNi nanoparticles with various molar ratios supported on MOF. Pd70Ni30/MIL-101(Cr) catalyst showed higher activity than monometallic counterparts and Pd + Ni physical mixture due to the strong synergistic effect of PdNi nanoparticles, high distribution... 

The solubility of Pd(NO3)2 in water is moderate whereas it is completely soluble in diluted HNO3 solution. Pd/MIL-101(Cr) and Pd/MIL-101-NH2(Cr) were synthesized by aqueous solution of Pd(NO3)2 and Pd(NO3)2 solution in dilute HNO3 and used for CO oxidation reaction. The catalysts synthesized with Pd(NO3)2 solution in dilute HNO3 showed lower activity. The aqueous solution of Pd(NO3)2 was used for synthesis of mono-metal Ni, Pd and bimetallic PdNi nanoparticles with various molar ratios supported on MOF. Pd70Ni30/MIL-101(Cr) catalyst showed higher activity than monometallic counterparts and Pd + Ni physical mixture due to the strong synergistic effect of PdNi nanoparticles, high distribution... 

In this study, magnesium oxide (MgO) nanoparticles are incorporated on carbon nanotubes (CNTs) to reinforce Mg-3Zn-1Mn alloy (ZM31 alloy) by semi-powder metallurgy, followed by hot extrusion, with the purpose of improving the mechanical and biological properties of Mg-based alloy. The microstructural analysis of the nanocomposites indicated a reduction in grain size of Mg alloy with the incorporation of CNTs with a maximum reduction of 61% (ZM31/CNTs), with further reduction in grain size (68%) detected when MgO integrated CNTs composites (ZM31/MgO-CNTs). The compression characteristics of the composites indicate an increase in ultimate compressive strength of 36% and 44%, respectively, with... 

WC-Co cemented carbides, including small angular tungsten carbides particles, are used extensively to improve wear resistance. Some additives can affect mechanical and wear properties of these materials. In this study, the effect of VC and (Ta, Nb)C content on wear of WC- 10Co were considered. The tests were performed at normal load of 230 N and sliding distance of 800 m up to 3200 m. Wear tests were carried out using dry sand/rubber wheel apparatus. Wear rate, standard and modified wear coefficients were calculated. The microstructures of prepared specimens were examined by optical microscopy. The morphological analysis of the worn surfaces was made by SEM. The results show that VC content... 

In present work, an attempt has been made to investigate the wear behavior of particle reinforced composites based on one of the proper magnesium alloys. The SiCP/QE22 composites and QE22 unreinforced specimens were produced via the powder metallurgy route. The volume fractions of SiC particles with three different shapes, i.e. sharp, blocky and round, were selected in the range of 10-25 vol.%. The dry sliding tests were conducted on unreinforced matrix and SiCP/QE22 composites using pin-on-disk apparatus, according to ASTM G99-95a standard. The applied loads were selected as 3, 5 and 20 N. The tests were carried out under sliding speeds of 0.5 and 1.2 m/s. In all tests, the sliding... 

In the present work, the fracture toughness data generated on the QE22 magnesium alloy as the matrix alloy and SiC particles reinforced composites using the short rod standard specimens. The short rod specimens of 18 mm diameter were prepared from the extruded rods in the extrusion direction. The fracture toughness values are primarily evaluated experimentally and then analytically by using mathematical methods. The suitability of these methods to predict this property was also discussed. Results showed that the incorporation of the SiC particles with three different shapes (i.e. sharp, blocky and round) decreases in general the fracture toughness of the QE22 Mg-alloy. This effect is... 

The dendritic structure of a cast ZA27 alloy can be transformed into a globular structure, if it is cold worked prior to being held in a semi-solid condition. The globular or the equiaxed particles are surrounded by the lower melting matrix. The dendritic structure was swaged and recrystallised prior to holding in a semi-solid state in this investigation. The semi-solid holding of the alloy at temperatures above and below that of peritectic reaction was carried out for various lengths of time. It was shown that the liquid fraction is decreased to below the peritectic temperature which leads to a reduction of lubrication between the solid globules and an increasing deformation force. Holding... 

This paper describes the influence of a fractional melting process on the reduction of interdendritic phases, which in turn have an impact on the tensile strength of ZA-27 alloys. The procedure consists of compressing a semi-solid specimen through a porous grinding disc, resulting on coarsening of the dendritic phase, reduction of the microporosity and homogenization of the alloy. © 2002 Elsevier Science B.V. All rights reserved