Sharif Digital Repository

Supervisory control and data acquisition (SCADA) infrastructures have so far been brought into the huge amount of focus since the need for a more reliable power system accosting with the catastrophic events of interruptions has been raised. Hence, benefiting from an automation technology which can remotely monitor and coordinate commands to enable immediate response and switching are obviously inevitable. This paper outlines an implementable method in response to the goal of placement of remote terminal units (RTUs) which are in charge for data acquisition and control in a power distribution system. In this light, a new practical methodology based on the robust decision making (DM) method,... 

This paper investigates a reliability-centered approach for the placement procedure of remote terminal units (RTUs) in power distribution systems. Entire attempt is contributed to incorporate the practical aspects interrelated with the problem, e.g. the accessibility to the candidate substations, the load point criticality, as well as the load probabilistic behavior and consequently the inevitable variation in the electricity price. The placement process is done through an optimization problem wherein the common reliability indices, as the decisive factors in the placement process, are going to be minimized. The approach is successfully applied to a real power distribution feeder of Iran's... 

Confronted with the power system restructuring trend reforming the past-regulated power systems, the need for a narrower insight on the costly maintenance strategies seems imperative. It falls within the realm of reliability centered maintenance to enhance the cost effectiveness of power distribution maintenance policies. From a practical point of view, this paper devises a novel approach on the basis of the analytical hierarchical process (AHP) accompanied by fuzzy sets theory to determine the most critical component types of distribution power systems to be prioritized in maintenance scheduling. In the presence of many qualitative and quantitative attributes, fuzzy sets can effectively... 

The online condition assessment of circuit breakers (CBs) has been increasingly requested by power utilities in recent years. Trip and close coil current (CC) signature is an effective and noninvasive parameter in CB online condition monitoring. This paper gives an insight into the impacts of the various failures on the coil current waveform, as well as on the CB operation time. The failures and their causes are categorized based on the outcome of these investigations. Finally, a new algorithm using trip/close CC is proposed to detect the mode and cause of CB incipient failures. In this study, the CC patterns are acquired by measurements carried out on (healthy and faulty) CBs of 72.5-kV and... 

Recognition of the circuit-breaker's (CB) vital role in reliable operation and protection of power systems (i.e., during energization, disconnecting loads, and clearing faults), helps to understand the requirement and importance of its maintenance management as well as maintenance scheduling. Condition-based maintenance (CBM), employing online monitoring (OLM) of CBs, has been long reported as the most practical maintenance policy on the power system CBs. There are a large number of CBs in a power system to be monitored; however, to address the financial limitations for OLM implementation (in utilities), a method will be proposed to find the most critical breakers for enforcing effectively... 

The proper and reliable operation of circuit breakers (CBs) directly affects the reliability and continuity of electricity services in a power systems. Condition-based maintenance (CBM) is the best economic CB maintenance strategy through its online monitoring (OLM) possibilities. Since there is a large number of CBs in a power system, to equip all CBs with OLM systems is not economically justifiable however. This paper, as the second part of a two-part paper, presents an effective optimization framework to find the optimal number of CBs to be monitored online as the kernel of CBM process. To prove its feasibility, the proposed approach is applied to the IEEE Roy Billinton Test System, which... 

We prepared porous silicon samples coated by continuous palladium layer in electroless process. Scanning electron microscopy (SEM) showed cauliflower-shape Pd clusters on the surface. I-V curves of Schottky like Pd/porous Si samples were measured in air and in hydrogen. These measurements showed a metal-interface-semiconductor configuration rather than an ideal Schottky diode. Variations of the electrical current in the presence of diluted hydrogen at room temperature revealed that the samples can sense hydrogen in a wide range of concentration (100-40,000 ppm) without any saturation behavior. Hydrogen sensing properties of these samples were investigated at room temperature for a duration... 

Purpose: This work aims to study factors, such as driver characteristics, environmental conditions, and vehicle characteristics, that affect different crash types with a special focus on distraction parameters. For this purpose, distraction factors are divided into five groups: cellphone usage, cognitive distractions, passengers distracting the driver, outside events attracting the driver’s attention, and in-vehicle activities. Methods: Taking the crashes that occurred in the USA into account, the crash types are divided into two main groups, single-vehicle crashes and two-vehicle crashes. Since there were different crash types (alternatives) in the dataset and the probable correlation in... 

This study provides a comprehensive literature review to summarize all contributing factors and the logit-based models that were used to predict the severity of crashes. Using the General Estimates Systems (GES) dataset, as a subset and a branch of the National Automotive Sampling System in the US, a Generalized Ordered Logit (GLM) model is developed to predict the crash severity. The developed severity model detects the most important parameters based on characteristics of the driver, the environment, the vehicle, the road, and the type of crash. This study aims to take a more in-depth look into the distraction-related factors as one of the most important groups of contributing factors to... 

Pure and Pd-doped WO3 Nanocrystalline tungsten oxide films on alumina substrates were prepared via sol-gel method from peroxopolytungstic acid. AFM, XRD, SEM, XPS methods were used to determine the surface morphology, grain size and layer composition. XRD analysis showed WO3 nanocrystalline particles in monoclinic phase and with average size of about 333nm, which was consistent with SEM analysis results. Sensing properties of samples toward H2 gas was studied. The sensitivity of WO3 nanocrystalline films was about 4 at 2300ppm (0.2%) H2 gas. Introducing Pd to the system led to an increase in the sensitivity about 2 orders of magnitude. The sensitivity of Pd: WO3 was about 400 at 2300ppmH2  

Porous silicon samples are obtained by electrochemical method on n-type wafers in room light. Scanning electron microscopy showed that the porous structure consisted of macropores under a thin microporous layer. Placing the samples in Pd-electroless solution causes the crakes inside the microporous layer and growth of the palladium particles in these crakes. However, removing the microporous layer by KOH solution with an ultrasonically assisted process makes the growth of rather uniform palladium particles on the surface in electroless plating. Variation of the electrical resistance in the presence of diluted hydrogen at room temperature revealed that the best samples have the ability to... 

Porous silicon samples were obtained from p+- and n-type silicon wafers. Gas sensing measurements showed that the electrical conductivity of porous Si on p+- and n-type wafers increases strongly and decreases weakly in the presence of methanol gas, respectively. Scanning tunneling spectroscopy (STS) indicates that the adsorption of methanol on the surface of n-porous silicon decreases the average density of states especially in the band gap. Fourier transform infrared (FTIR) spectroscopy reveals that after methanol exposure partial surface oxidation occurs which produces electron traps as well as methanol adsorption on the porous surfaces. These observations imply that the number of... 

Porous poly-silicon (PPS) samples, obtained by electrochemical anodization of p-type poly-silicon wafers, were doped with Pd by the electroless process. Rutherford backscattering spectroscopy shows that Pd has diffused a few micrometres into the PPS layer. Scanning electron microscopy and energy dispersive x-ray analysis results demonstrate the presence of Pd as dispersed clusters on the surface. The variation of the electrical resistance in the presence of dry air diluted with hydrogen at room temperature shows that Pd/PPS samples have the ability to sense hydrogen at levels down to several thousands of ppm. This value is far below the flammability limit of hydrogen gas. It was found that... 

The need for supporting the ever-growing number of multi-computers in the contemporary Internet has persuaded researches worldwide to search for suitable underlying network topologies with desirable properties. Even in the presence of speedy optical technologies, the arrangement of nodes in a network can be highly influential. Among all the topologies investigated so far, k -ary n-cubes have been reported to be widely adopted in the literature. But in hybrid networks, where the network is composed of a mixture of different types of topologies, the type and size of k-ary n-cubes can greatly affect the performance factor of the network. In this paper, we study and compare the performance... 

So far, the need for power systems to be control automated has been approached. Moreover, the advent of smart technological infrastructures calls for a more systematic and well-designed schemes for data acquisition process. Hence, Remote Terminal Units (RTUs) are going to be considered as a crucial part of smart grid puzzle in power distribution systems. This paper aims to present a novel practical approach to have the RTU placement dilemma unraveled in power distribution systems. Practically approaching in this paper, some pragmatic factors of major importance in this respect are introduced. A framework with which the utility's experts' knowledge could be efficiently exploited is presented... 

To obtain wider openings than those provided by Chevron bracing, the braces are cranked and connected to the frame corner by an additional brace to form double y-shaped bracings. However, y-bracings are prone to instability and out of plane buckling, accompanied by low hysteretic energy absorption. An experimental research program, focused on y-bracing, was conducted at the BHRC structural engineering laboratory. Specimens presented in this paper include three full-scale single bay frames, with symmetric y-bracing of different cross sections and connection types. In addition, one specimen with Chevron bracing was tested as a reference. A quasi-static cyclic loading was applied increasingly... 

In this paper, recovery of penicillin G from mycel-containing fermentation broth through physical extraction is investigated. The values of degree of extraction are evaluated as a function of media pH, partition coefficient between aqueous and organic phases for undissociated acid and the pKa of penicillin. The pH variations were measured during extraction operation and the optimum pH value for penicillin G recovery considering its decomposition was obtained. The mass transfer analysis of the extraction system was carried out using two-resistance mass transfer theory. The overall as well as aqueous and organic phase mass transfer coefficients were determined. The investigated mass transfer... 

We fabricated gas sensors based on field ionization from multiwalled carbon nanotube (MWCNT) arrays grown on porous silicon templates. MWCNTs were grown through thermal chemical vapor deposition. We measured breakdown voltages, discharge and pre-discharge currents of the device for various gases in different concentrations. Our gas ionization sensors (GIS) presented good sensitivity, selectivity and short response time. The GISs based on porous substrates showed higher discharge current and good mechanical stability in comparison to those which were fabricated on polished silicon substrates. Additionally, we applied a high electric field to align CNTs. This increased the pre-breakdown... 

Among all proposed structures for optical networks, the optical packet switching (OPS) scheme, due to its practical implementation of IPs in an optical configuration and the consequent advantages, is a prizeworthy candidate for being employed in metropolitan area network and local area network communication levels. One of the few problems frequently met using the OPS structure in the fiber-optics realm is the lack of optical buffers, thus deteriorating the system's flexibility and quality of service. For example, optical label switching networks that have been developed recently based on the generalized multiprotocol label switching protocol, profoundly suffer from this setback which is...